• RELEVANCY SCORE 4.27

    DB:4.27:Host Name Error Message Opening Virtual Machine 97




    When starting a virtual machine in VMware server I get the following error message

    Error opening the remote virtual machine XXX:8333\16 The host name could not be resolved.

    Any help would be appreciated

    DB:4.27:Host Name Error Message Opening Virtual Machine 97


    The VM tools was loaded to the cd drive awaiting installation, now working fine

    cheers

    Brenden Ward

    System Support Analyst

    INEX

    University of Newcastle

    Newcastle upon Tyne

    NE1 7RU, UK

    http://www.inex.org.uk

    Tel: +44 191 222 5988, Fax: +44 191 222 3528

    This e-mail and any files and attachments transmitted with it are confidential and/or privileged. They are intended solely for the use of the intended recipient(s). The content of this e-mail and any file or attachment transmitted with it may have been changed or altered without the consent of the author.

    If you are not the intended recipient, please note that any review, dissemination, disclosure, alteration, printing, circulation or transmission of this e-mail and/or any file or attachment transmitted with it, is prohibited and may be unlawful. If you have received this e-mail or any file or attachment transmitted with it in error please notify the Information Systems Manager, INEX, Herschel Annex, Newcastle upon Tyne, NE1 7RU, UK, enquiries@inex.org.uk

  • RELEVANCY SCORE 3.94

    DB:3.94:Error Opening Web Console da





    Error opening the remote virtual machine wkux014437:8443\16:

    The host name could not be resolved.

    DB:3.94:Error Opening Web Console da


    Looks like this has been answered correctly elsewhere: http://communities.vmware.com/thread/136898?tstart=0

    Fix: add the host server name and IP in the hosts file at \system32\drivers\etc

  • RELEVANCY SCORE 3.65

    DB:3.65:Compute Resource 'Clustername' Does Not Have A Host Available That Is Attached To Storage Required For This Virtual Machine cf





    I'm working on SRM 4.0 and have completed the setup and configuration, but when I attempt to test the recovery plan, I'm getting the following error message during recovery:

    Error: Recovery failed for virtual machine 'VM-NAME'. Compute resource 'Cluster-Name' does not have a host available that is attached to storage required for this virtual machine.

    I've confirmed that the hosts in the recovery site have full access to the replicated LUN/volume for the VM. Any other suggestions?

    DB:3.65:Compute Resource 'Clustername' Does Not Have A Host Available That Is Attached To Storage Required For This Virtual Machine cf


    need to see the recovery site SRM log to see what is wrong here.

    check that in the inventory mapping screen at the protected site you have not inadvertently mapped a cluster object incorrectly...in reality you do not even need to map cluster objects, resource pools are fine. if you had mapped the protected site cluster object to a recovery site cluster that included hosts not mapped to the recovery array that would generate this error.

    if you do not want to attach the log to a public forum then have you logged an SR with VMware?

    cheers

    Lee

  • RELEVANCY SCORE 3.64

    DB:3.64:Can't Use The Remote Console 7k


    Hi,

    I have a trouble with the Remote Console on a Linux Fedora 10 x86_64 host. The VMWare server was installed on a Windows Vista x86 host, and the Web acess is working fine. I installed the Remote Console on the Fedora, but i have this message :

    Error opening virtual machine 48: An error occured while transferring data.

    I have no more informations in Windows's or Linux logs.

    An idae?

    Best regards

    KCO

    DB:3.64:Can't Use The Remote Console 7k


    I test without any firewall on my computers, it doesn't work. But the remote console works fine in localhost. The WebUI works in my Linux host.

  • RELEVANCY SCORE 3.53

    DB:3.53:Memory Counters jf



    Can anybody please explain (or point to documentation about) the exact meaning of the "Host mem - MB" and "Host mem - %" columns I see in the vSphere client while selecting a node and opening the "Virtual machines" tab?

    The "Host mem - %" is the percentage of which value? Host menmory? Virtual machine "physical" memory? What else?

    Regards

    marius

    DB:3.53:Memory Counters jf


    Can anybody please explain (or point to documentation about) the exact meaning of the "Host mem - MB" and "Host mem - %" columns I see in the vSphere client while selecting a node and opening the "Virtual machines" tab?

    The "Host mem - %" is the percentage of which value? Host menmory? Virtual machine "physical" memory? What else?

    Regards

    marius

  • RELEVANCY SCORE 3.45

    DB:3.45:Delete Environment Hangs ak


    Hi
    We try to delete an environment from the library but it says that the machine is allready deleted in SCVMM. I don't know why its gone, but the problem is now that the job hangs in MTLM and there's no way to cancel it. There is no job in SCVMM either,
    so what do I do?
    the full error message:
    Environment message: Type=Error; Message=TF259042: Team Foundation Server has found some problem with one or more virtual machines. Review
    errors on virtual machines and resolve those. If problem persists, contact your administrator.;

    Machine messages:

    Machine name: Vista_x86_UK_SP2_IE8_OF2010_LabAgent

    Machine message: Type=Error; Message= TF259109: Team Foundation Server found the virtual machine in deleted state. The corresponding virtual
    machine at SCVMM server was deleted. Contact your system administrator.
    Additional information: The name of the virtual machine in Virtual Machine Manager is Lab_d3468d28-4f73-4925-949d-d9294b5ab626.;

    regards
    Kim

    DB:3.45:Delete Environment Hangs ak

    Hi,
    FYI, I'm also getting the same error, althoughwhen trying to deploy an environment from library.
    the corresponding virtual machine at scvmm server was deleted is visible in the Lab Manager error description. I don't see any errors in SCVMM and can manually deploy the same VM without issue.

  • RELEVANCY SCORE 3.44

    DB:3.44:Error 803 Vmm 2012 R2 While Recreating Vdi Vm From Rds c9


    Hi All,
    Back Again for your help in System Center Virtual Machine manager 2012 R2.

    Issue : In my RDS VDI 2012 environment we are managing Virtual machine and host with VMM 2012 R2, However when we Recreate these Virtual Machine while Patching or resource upgrade RDS recreate all the desktop fine but in System Center VMM I will got duplicate
    machine from same name and one with the ERROR : 803 (Virtual machine VDIPS01 already exists on the virtual machine host RDSVH01 , Specify a new name for the virtual machine, and then try the operation again.

    please help.

    DB:3.44:Error 803 Vmm 2012 R2 While Recreating Vdi Vm From Rds c9


    Microsoft recently release a KB article describing that This is a known issue in System Center 2012 Virtual Machine Manager, System Center 2012 Virtual Machine Manager Service Pack 1 (SP1), and System Center 2012 R2 Virtual Machine Manager.

    Workaround:

    http://support.microsoft.com/kb/2974441

  • RELEVANCY SCORE 3.39

    DB:3.39:Windows Server 2003 Does Not Support The Buslogic Scisi Adapter 1s


    Hi

    Get the following error massage when starting virtual host. Virtual host start fine. Just wondered why this error massage shows up.

    Converted the server onto and ESX 3.5 U3 box with enterprise convertor.

    Message on NAME on NAMEVS in ha-datacenter: Your guest operating system is windows server 2003 and you have one or more virtual scsi devices installed in your virtual machine. Please be aware that windows server 2003 does not support the buslogic scisi adapter that vmware esx server currently uses for its virtual scsi devices. if you have not done so already, you need to install our driver in the virtual machine. You can download..... Click OK to conitinue or Cancel to abort.

    Thanks

    CT

    DB:3.39:Windows Server 2003 Does Not Support The Buslogic Scisi Adapter 1s


    ?

    2k3 natively supports LSI-controllers as used by VMware.

    When your 2k3 boots this means you either simply use a LSI-controller for the virtual hardware or you already added a driver for the BUS-logic controller.

    If you want check the vmx-file - you can look it up there.

    If the vmx says

    scsi0.virtualDev = lsilogic

    this means your VM use the LSI-logic controller

    If the vmx says

    scsi0.virtualDev = buslogic

    or doesn't have such an entry it uses a virtual BUS-logic controller

    So in both cases this message is just a warning that you can ignore - or click away for ever

    ___________________________________

    description of vmx-parameters: http://sanbarrow.com/vmx.html

    VMware-liveCD: http://sanbarrow.com/moa.html

  • RELEVANCY SCORE 3.37

    DB:3.37:A Virtual Machine Or Template Having The Same Name Is Already Registered. Server Error: The Specified Key, Name, Or Identifier Already Exists. pf



    Hello Everyone,

    I have few virtual machines on an ESX host , the state of these virtual machines is showing as disconnected.The ESX host hosting those virtual machines is also disconnected. I was going to reinstall ESX on that host but cant do so untill i get these few VM's registered on another host. I am not able to remove these machines from the inventory and when i try to readd these machines to the inventory while browing them from the datastores i get an error "A virtual machine or template having the same name is already registered. Server Error: The specified key, name, or identifier already exists."

    The ESX host which is hosting these VM's isnt responding either.

    Any help will be appreciated

  • RELEVANCY SCORE 3.28

    DB:3.28:Running Multilpe Concurrent P2v Clones c1



    For reasons too mundane to include I want to run 3 clones of my physical machine.

    Building the clone using VMware Converter went without a hitch. The problem arises when I try to run virtual machines with the same name on my network (error message on opening). Is there anyway to rename the virtual machines?

    Regards

  • RELEVANCY SCORE 3.11

    DB:3.11:Domain Logon 1p



    We cloned the host and run it as a virtual machine inside the host. Host will logon to domain. Virtual machine will log on once to domain but not after a reboot. Gives error that account is not present but it is present. Sid and name already changed. Both machines XP.

    DB:3.11:Domain Logon 1p


    It will logon on once but not after a host reboot. The error says there is no account for this computer. But of course there is an account

  • RELEVANCY SCORE 3.09

    DB:3.09:Converter Failure - "Error 2 While Opening Vstor2 Driver's Control Device" x1


    Hi All,

    just starting off with our VMware Testing and am getting an error when trying to convert a Physical Server (a Virtual Iron virtual machine actually) to a virtual machine on an ESXi 4.0 host. The conversion always fails at 95% with the following message in the logs

    Error 144 mounting the destination volume

    Vmount library: Error 2 while opening VSTOR2 driver's control device

    have tried the conversion from the source machine, from the vCenter Server and from a third machine all with the same result. As target i have chosen the vCenter Server and the ESXi Server - again the same result. Have tried virtual machine versions 4 7 as well as changing options on the Disk Controller from 'Preserve Source' to 'SCSI Bus Logic'. Always the error with the CloneTask and the VSTOR2! Target is an iSCSI Volume mapped to the ESXi Server. Have been searching around the communities here but not yet found a solution - can anyone point me in the right direction before i pull what little remains of my hair...

    thanks in advance!

    William

    DB:3.09:Converter Failure - "Error 2 While Opening Vstor2 Driver's Control Device" x1

    Just a note if anyone is encountering a similar issue:

    while i have no definitive proof, i believe this failure was caused by not having enough RAM in the target host. The host had only 2GB of RAM as it is just serving as a temporary migration target. Since that time i have successfully migrated other Linux machines to that same target host using the converter and have also used the converter to successfully migrate Windows 2003 servers to another host which is outfitted with 32GB RAM. I must say - when the converter works as expected it is automagical

    thanks,

    William

  • RELEVANCY SCORE 3.08

    DB:3.08:Remote Console Connection To Server Name Times Out cs


    I just installed 2.0b2 on a Windows 2003 server. When I connect to the Web Access interface using the server name (archer), the web access interface comes up with no issues. However, when I try to open a console, it times out due to a name resolution failure. The error I get is:

    VMware Remote Console

    Error opening the remote virtual machine archer:8333\96:

    The host name could not be resolved.

    This error occurs both when opening the console from the Web Access interface and from desktop shortcuts. As soon as I change the host name to local host, everything works great.

    DB:3.08:Remote Console Connection To Server Name Times Out cs

    Using the host IP address as a work-around worked fine for me (opening the console). However I did notice yet another bug;

    If you have VMTools upgrade setup (the media is loaded on the guest OS); No matter what I tried I can't connect to the console anymore. The moment I eject the VMTools media from the Guest; I can connect to the console via the host IP address again. Interest bug huh?

  • RELEVANCY SCORE 3.07

    DB:3.07:Error Opening The Remote Virtual Machine Hostname:8333\16 - A Connection To The Host Could Not Be Established. ss


    I set up VMware server 2 on a windows XP machine with SP3 and had it all running fine. I installed Vista to run as a client and created a desktop shortcut. Then shut dowm my now I cannot get it to run I just get the following error message:

    "Error opening the remote virtual machine lt;hostnamegt;:8333\16:

    A connection to the host could not be established."

    When I try to connect to theVMWare Server Home Page I get the following Internet Explorer error:

    "Internet Explorer cannot display the webpage"

    It seems a numebr of people are having similar problems but I cannot find any solutions to my problem.

    Help would be much appreciated.

    Thank you.

    Nik

    DB:3.07:Error Opening The Remote Virtual Machine Hostname:8333\16 - A Connection To The Host Could Not Be Established. ss


    I have tried something which helped me to overcome this problem (this will work on all Windows OS)

    1. Install microsoft loopback adapter

    2. Give some IP and DNS (in my case IP-1.1.1.1 and DNS- 1.1.1.1/1.1.1.2)

    Now it will start working.

  • RELEVANCY SCORE 3.06

    DB:3.06:Vmware Player 5 Won't Play Existing Machine x7



    I have been a virtual XP on Win 7 host for several years under various versions of VMware Player since v3.

    After upgrading to ver 5 I cannot launch the existing virtual XP machine.

    The error message cites the policies of the virtual machine as being too old.

    AWhat can ber done to make it run.

    DB:3.06:Vmware Player 5 Won't Play Existing Machine x7


    Have a look at Starting a virtual machine in Workstation 9.x or Fusion 5.x fails with the error: This virtual machine's policies are too old to be run by this version of VMware (2034362) which is also applicable to VMware Player 5.x. See also the hyperlinks with the KB for further assistance.

  • RELEVANCY SCORE 3.06

    DB:3.06:"General System Error Occured" On Server 2.0 Beta 2 31



    After restarting the host PC (Server 2003R2) i get the message "general system error occured: unknown error" immediately after starting virtual machine.

    Can someone help please.

  • RELEVANCY SCORE 3.05

    DB:3.05:Remote Console Will Not Open! 3j


    I don't suppose you know and answer to this one.

    This URL Starts VMserver OK https://vm-ware:8333/ui/#{e:"Folder}}

    I cannot get to the console the following error appears after i start the VM and go to open the console?

    Error opening the remote virtual machine vm-ware:8333\16:

    The host name could not be resolved.

    Paul

    DB:3.05:Remote Console Will Not Open! 3j

    Again thanks for that Peter, so simple.

    Paul

  • RELEVANCY SCORE 3.03

    DB:3.03:Issue When Importing Machine Using Vm Convertor z8



    Get the following error message in Virtual Center when running VMWare converter to convert a physical machine to virtual.

    Name: Create Virtual Machine

    Status: Number of virtual devices exceeds the maximum for a given controller.

    I have successfully used the VMWare Converter to migrate other machines.

  • RELEVANCY SCORE 3.02

    DB:3.02:Scvmm2012sp1 : Livevm From Cluster Hyper-V 2012 To Cluster Hyper-V 2012 Failed 3a


    Bonjour,

    Je tente de réaliser un live migration de machine virtuelle depuis un cluster Hyper-V 2012 vers un autre cluster en 2012.
    Je réalise ces opération depuis le logiciel SCVMM2012SP1 avec les clusters correctement ajouté à la console.
    Et je tombe sur ce message d'erreur :
    Error (12700)
    VMM cannot complete the host operation on the iasphy05.ias.local server because of the error: Virtual machine migration operation for 'IASVM1' failed at migration source 'IAS'.

    The Virtual Machine Management Service failed to establish a connection for a Virtual Machine migration with host 'SUP':

    General access denied error (0x80070005).
    The Virtual Machine Management Service failed to establish a connection for a Virtual Machine migration because the destination host rejected the request: General access denied error (0x80070005).
    Unknown error (0x8001)
    Recommended Action
    Resolve the host issue and then try the operation again.

    Et j'ai ce message lorsque je tente la migration inverse :
    Error (12700)
    VMM cannot complete the host operation on the SUP server because of the error: Virtual machine migration operation for '' failed at migration source 'SUP'.
    Virtual machine migration for '' failed because configuration data root cannot be changed for a clustered virtual machine.

    Unknown error (0x8005)
    Recommended Action
    Resolve the host issue and then try the operation again.

    Lorsque je fais la migration de la VM en mode offline, celle ci passe correctement.

    merci de votre aide sur le sujet.
    Cordialement
    Guillaume

    DB:3.02:Scvmm2012sp1 : Livevm From Cluster Hyper-V 2012 To Cluster Hyper-V 2012 Failed 3a

    Bonjour Guillaume,
    Est-ce que vous avez activé le live migration sur chaque cluster ?
    Est-ce que l'authentification utilisée est identique de chaque côté ?
    L'article suivant pourra vous aider sur les pré requis:
    http://www.vinfra.ch/2013/04/hyper-v-2012-deplacer-une-vm-dun-hote-vers-cluster/

    La configuration pouvant également être réalisée depuis vmm.

    Il semble qu'il agisse, à priori d'un problème d'authentification entre vos deux clusters (0x80070005).

    Guillaume http://www.vinfra.ch

  • RELEVANCY SCORE 3.02

    DB:3.02:Java.Rmi.Unknownhost Error 9s



    Hello,

    I installed Avamar Virtual editon Version 5, when I try to connect to it using Administration console i got the below error.

    java.rmi.unknownhostException: unknown Host

    java.net.unknownhostException: Host name

    I installed the Java and the admin console, also I installed it on second machine with same error.

    Please advice.

    Thanks a lot.

    Regards,

    Ahmed Salah

    DB:3.02:Java.Rmi.Unknownhost Error 9s


    This is a known limitiation of the Avamar Administrator.

    There can only be one RMI address (defined in mcserver.xml or detected automatically if not specified) and that address must resolve to the IP where the utility node (or single node server) can be reached for that environment. For environments where the Avamar Server has many IP addresses defined, the usual workaround is to specify the short name of the utility node as the RMI address and configure DNS or /etc/hosts entries that point the hostname to the correct IP for each client subnet.

  • RELEVANCY SCORE 3.01

    DB:3.01:Error During Migration Of A Vm 8s


    I recieved this error when trying to migration a VM to a remote server using Windows Server "8" on both Servers:
    PS C:\Users\Administrator Move-VM -Name OnTheMove -DestinationHost $RemoteServer
    Move-VM : Virtual machine migration operation for 'OnTheMove' failed at migration source 'SERVER-1950-01'. (Virtual
    machine ID 172C44E1-E34B-4896-B450-B41CB037638D)
    The Virtual Machine Management Service failed to establish a connection for a Virtual Machine migration with host
    'Server-1950-02': An existing connection was forcibly closed by the remote host. (0x80072746).
    Failed to send data for a Virtual Machine migration: An existing connection was forcibly closed by the remote host.
    (0x80072746).
    At line:1 char:1
    + Move-VM -Name OnTheMove -DestinationHost $RemoteServer
    + ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
    + CategoryInfo : NotSpecified: (Microsoft.Hyper...VMMigrationTask:VMMigrationTask) [Move-VM], Virtualizat
    ionOperationFailedException
    + FullyQualifiedErrorId : OperationFailed,Microsoft.HyperV.PowerShell.Commands.MoveVMCommand

    Any ideas? Thanks.

    DB:3.01:Error During Migration Of A Vm 8s

    Hi,
    I would suggest you to post your question at the following link.
    http://technet.microsoft.com/en-us/ms772425

  • RELEVANCY SCORE 3.00

    DB:3.00:Problem Cloning Virtual Machine mp



    Hi,

    When I try to clone a virtual machine from one esx server to another, I get the following error message after a random period of time

    "connection to host lost"

    and the cloning process stops, leaving the destination host in an unmanageable state (MUI stops responding).

    Can somebody help me out here?

    Regards,

    Werner

    DB:3.00:Problem Cloning Virtual Machine mp


    Hi,

    When I try to clone a virtual machine from one esx server to another, I get the following error message after a random period of time

    "connection to host lost"

    and the cloning process stops, leaving the destination host in an unmanageable state (MUI stops responding).

    Can somebody help me out here?

    Regards,

    Werner

  • RELEVANCY SCORE 2.99

    DB:2.99:Test Controllers Testrunstorage Has Filled Up Hard Drive sm


    The background
    We have run into a situation where our tests began to not run for no apparent reason on our Test agent where our tests run from MTM. Looking around for a while, I came across in Lab Management finding warnings that something was wrong and that the Testing
    Capability has failed and had a link button offering to Repair Testing capability detailing the Controller machines Name. There was also a link to View details which only said the below which I found rather useless. I thought I would go through
    the layers of servers (which are all Virtual) from controller to agent to Application servers to see where the problem was and luckily I think I found it straight away on the Controller. It seems that there was no disk space left which even stops me from opening
    the Controller Configuration Tool. Looking around the server to find the source of why the server had no disk space left I found that the Service account (that the Controller runs under) user folders was 21GB when the virtual server was only 40GB. Specifically
    I found it to be this folder: C:\Users\AccountName\AppData\Local\VSEQT\QTController\TestRunStorage. which obviously holds the results.

    My question(s) are this:

    Is there any way to manage these test results without having to just delete the folders? ie is there a configuration option somewhere to delete results older than a certain date or similar?
    If i have to just Delete the folders, will that break links to the Test results held in MTM or is this just an intermediary location for the results before they are put somewhere else to be referenced from the MTM?

    Please let me know if you need any more details.
    Thanks
    Lab Manager View Details output
    Environment message: Type=Error; Message=TF267056: The environment is not ready to run tests because Team Foundation Server could not complete the operation to update the following environment: ART.All Hosts_Development Test Hosts.VirtualTestEnvironmentName,
    controller ControllerName:PortNumber. The test controller returned the following error: This operation is not allowed while a test is running.. Make sure the test controller is online, the firewall on the test controller is not blocking the
    connection, and the Team Foundation Server has required permissions to connect to the test controller.;

    --------------------------------------------------
    Environment message: Type=Information; Message=Additional information is available about the workflow capability.;

    Machine messages:

    Machine name: TestAgentServerName

    Machine message: Type=Information; Message=TF266026: Team Foundation Server is configuring the workflow capability on this virtual machine. If this message persists, click 'Repair Workflow Capability' and make sure that the account under which the following
    service is running is a member of the Administrators group on the machine: Visual Studio Team Foundation Build Service Host.;

    Machine name: ApplicationServerName

    Machine message: Type=Information; Message=TF266026: Team Foundation Server is configuring the workflow capability on this virtual machine. If this message persists, click 'Repair Workflow Capability' and make sure that the account under which the following
    service is running is a member of the Administrators group on the machine: Visual Studio Team Foundation Build Service Host.;

    Machine name: SQLServerName

    Machine message: Type=Information; Message=TF266026: Team Foundation Server is configuring the workflow capability on this virtual machine. If this message persists, click 'Repair Workflow Capability' and make sure that the account under which the following
    service is running is a member of the Administrators group on the machine: Visual Studio Team Foundation Build Service Host.;

    Machine name: WebServerName

    Machine message: Type=Information; Message=TF266026: Team Foundation Server is configuring the workflow capability on this virtual machine. If this message persists, click 'Repair Workflow Capability' and make sure that the account under which the following
    service is running is a member of the Administrators group on the machine: Visual Studio Team Foundation Build Service Host.;

    --------------------------------------------------

    DB:2.99:Test Controllers Testrunstorage Has Filled Up Hard Drive sm

    Hi,
    I am posting the code of a PowerShell scriptwhich I implemented to more reliably take care of that task. I created an item in Windows Task Scheduler to run that script twice a day.

    ### This script would be scheduled to run with the Windows Task Scheduler

    # Define global variables
    $targetCompareTime = (Get-Date).AddDays(-1)
    $testControllerUserName = testuser

    # First, delete test run output directories (where .trx files are stored)
    $targetRootPath = C:\TestProcedureReports\TestResults

    $targets = @(Get-ChildItem $targetRootPath | Where {$_.psIsContainer -eq $true -and $_.CreationTime -lt $targetCompareTime})

    if ($targets.Count -ne 0)
    {
    Deleting:
    $targets
    $targets | Remove-Item -Recurse -Force
    }

    # Second, delete controller test run deployment directories
    $targetRootPath = C:\Users\$testControllerUserName\AppData\Local\VSEQT\QTController
    $targetExclude = TestRunStorage

    $targets = @(Get-ChildItem $targetRootPath -Exclude $targetExclude | Where {$_.psIsContainer -eq $true -and $_.CreationTime -lt $targetCompareTime})

    if ($targets.Count -ne 0)
    {
    Deleting:
    $targets
    $targets | Remove-Item -Recurse -Force
    }

    # Finally, delete controller test run storage directories
    $targetRootPath = C:\Users\$testControllerUserName\AppData\Local\VSEQT\QTController\TestRunStorage

    $targets = @(Get-ChildItem $targetRootPath | Where {$_.psIsContainer -eq $true -and $_.CreationTime -lt $targetCompareTime})

    if ($targets.Count -ne 0)
    {
    Deleting:
    $targets
    $targets | Remove-Item -Recurse -Force
    }

  • RELEVANCY SCORE 2.99

    DB:2.99:Error Message When Adding A New Virtual Machine 8p



    Hi Everyone,

    I am new to VM and I'm obviously going to sound as an idiot on this question that I'm going to ask but after adding a datastore and about to click the finish button to install or add a new virtual machine on my VM server esx3.5, I get this error message saying "a general system error occured! Read-only file system" I know what read-only means but how can I make my VMFS writeable or disable that read only on the host so that I can add/install a Virtual machine on the host?

    DB:2.99:Error Message When Adding A New Virtual Machine 8p


    hi and welcome. may we know what kind of storage are you attaching it to? have a read here: http://communities.vmware.com/message/1006572

  • RELEVANCY SCORE 2.99

    DB:2.99:Error Opening The Remote Virtual Machine 39



    I have VM Server beta 2.0 installed and I created a guest machine.

    However, when I try to use the remote console where it tells me to "click anywhere to open the virtual machine", but when I click I get this error.

    "Error opening the remote virtual machine...thThe host name could not be resolved"

    How do I fix this?

    Thanks,

    ik2003

    DB:2.99:Error Opening The Remote Virtual Machine 39


    Put IP of vmware server and its name to host OS "hosts" file?

  • RELEVANCY SCORE 2.98

    DB:2.98:Error Opening The Remote Virtual Machine %Servername%:8333\176: A Connection To The Host Could Not Be Established j9



    I have a server with VMware 2.0 RC2. I changed the IP Address of server but when I execute the remote console virtual machine it appears this following message: Error opening the remote virtual machine %servername%:8333\176: A connection to the host could not be established

    I need your help.

    thanks.

    DB:2.98:Error Opening The Remote Virtual Machine %Servername%:8333\176: A Connection To The Host Could Not Be Established j9

    I tried to forward 902 too, and it works perfect, thanks

    PS: I forward 8333, 8222, and 902. The source port number is the same with the destiny port number.

  • RELEVANCY SCORE 2.98

    DB:2.98:Hyper-V Virtual Ethernet Adapter Not Working Probperly - Code 31 On Host jj


    I have a Windows 8.1 machine with Hyper-V installed. From a clean Hyper-V configuration I open Virtual Switch Manager, create an External switch with Allow management operating system to share this network adapter, click
    OK. Everything seems to work properly but the host loses network connectivity.
    Opening Device Manager, the Hyper-V Virtual Ethernet Adapter is shown under the Network Adapter section with a yellow triangle, and the following message:
    This device is not working properly because Windows cannot load the drivers required for this device. (Code 31)

    An object ID was not found in the file.

    I tried Uninstalling the device, seems to work, but the device doesn't actually remove. I tried removing and re-adding the Hyper-V feature completely, no difference. Triedscf
    /scannow, no problems.
    System and Application logs show no errors. The Hyper-V-VMMS Networking log shows the following:
    Log Name: Microsoft-Windows-Hyper-V-VMMS-Networking
    Source: Microsoft-Windows-Hyper-V-VMMS
    Date: 3/27/2014 11:53:07 AM
    Event ID: 26088
    Description:
    Failed to apply static IP settings to internal Ethernet adapter {A813DE9A-BE70-4FAE-AD31-BE4D54505A4B} ('885435B8-BE65-4EE9-826D-AB56035237ED'): Unspecified error (0x80004005).

    If I try to remove the Virtual Switch in Hyper-V Virtual Switch Manager I get this in that same log:
    Log Name: Microsoft-Windows-Hyper-V-VMMS-Networking
    Source: Microsoft-Windows-Hyper-V-VMMS
    Date: 3/27/2014 12:19:47 PM
    Event ID: 26142
    Description:
    Failed while removing virtual Ethernet switch.

    Trying to remove the Virtual Switch leads to an error:
    Error applying Virtual Switch Properties changes

    Failed while removing virtual Ethernet switch.

    DB:2.98:Hyper-V Virtual Ethernet Adapter Not Working Probperly - Code 31 On Host jj

    The issue sounds rooted in your network card driver. Is there any type of management or monitoring agent, or do you run any type of software based VPN?
    Also, ifyou have any other virtualization engine installed, you will have issue.

    Not to mention there are some firewall applications that will also cause problems as they won't let Hyper-V do what it needs to.
    Brian Ehlert
    http://ITProctology.blogspot.com
    Learn. Apply. Repeat.
    Disclaimer: Attempting change is of your own free will.

  • RELEVANCY SCORE 2.97

    DB:2.97:Console Error!! 8f


    Hi All

    I am a confident VMware Server 1.X user. I have recently installed a version of windows 2k8 as the host. I made a quick go at installing server V1.04 and had anumber of issues and errors. Again on a quick search of the forums, there seemed to be a number and all replies suggested to look at Beta 2.0. So this is is what I had done.

    I had previously given the host the web server role so that it installed IIS 7.0 and additional apps/services such as asp and .Net etc. I then ran through the setup without any errors. Managed to connect to the new VMware Infrastructure Web Access (IWA), created a virtual machine, then powered it on. Then stumbled around looking for the console which when I click on the Click anywhere to openthe virtual machine, I get the following error..

    Vmware Remote Console: Error opening the remote virtual machine Physicalhost:8333\16: The host name could not be found. (note the backslash is not a typo on my behalf)

    When I type physicalhost:8333 into a browser it takes me to the previous IWA screen. So why can I not get to the console of the machine??

    DB:2.97:Console Error!! 8f

    Hi eaperezh

    Thanks for your reply, I take your point on board however if you note that I tried just connecting to the physicalhost with that port number and was able to connect through fine. It was the \16 bit that was causing the issue. Note my other post about the shortcut.

  • RELEVANCY SCORE 2.97

    DB:2.97:Unable To Connect To Guest When Host Is Not Connected To Internet!! sp


    I know this may sounds odd, but when I was out at a library I noticed I couldn't connect to the remote virtual machine. and when I could get back home everything was fine. Then I disabled my wireless network card at home and I got the same error. "error opening the remote virtual machine .... an unexplained error occured"

    Any suggesstions?

    DB:2.97:Unable To Connect To Guest When Host Is Not Connected To Internet!! sp

    Hi there

    I'd the same problem. And as I like to use "VMWare Server 2.0" in seperate Test-Environment I'm not happy with the "... unexplained error occured...".

    Now I configured my real LAN-Adapter Settings to use a imagenary "Gateway-Adress" and "DNS-Server-Adress". And wow I can access the console out of the "VMWare Infrastructure Web Access).

    Hope this may help you

    Helmut, the Germaneer

  • RELEVANCY SCORE 2.97

    DB:2.97:Problem Connecting Server 1.0 Console To Gsx 3.1 Host p1



    I have following strange behaviour when using the VMware Server 1.0 Console to connect to a host with VMware GSX 3.2.1. When supplying the hostname, I get following error message:

    There was a problem connecting.

    Host address lookup for server without problems from the same machine where the console is running.

    When I use the GSX Virtual Machine console (installed on the same client), I can connect succesfully to the host by both methods (supplying host name or IP).

    Has anybody an explanation for this behavior and/or solution?

    Thanks in advance![i][/i][i][/i][i][/i]

    DB:2.97:Problem Connecting Server 1.0 Console To Gsx 3.1 Host p1


    I have following strange behaviour when using the VMware Server 1.0 Console to connect to a host with VMware GSX 3.2.1. When supplying the hostname, I get following error message:

    There was a problem connecting.

    Host address lookup for server without problems from the same machine where the console is running.

    When I use the GSX Virtual Machine console (installed on the same client), I can connect succesfully to the host by both methods (supplying host name or IP).

    Has anybody an explanation for this behavior and/or solution?

    Thanks in advance![i][/i][i][/i][i][/i]

  • RELEVANCY SCORE 2.96

    DB:2.96:Question About The Virtual Address For Oracle Fail Safe 3.4.2 jm


    When I tried to enter the virtual server name, I got the error message "The host name does not resolve into an IP address...". Is the virtual server name needs to be registered in the DNS server or the Window administrator will define it?Thank you in advance!Youngchi

    DB:2.96:Question About The Virtual Address For Oracle Fail Safe 3.4.2 jm

    Hi Youngchi, Oracle uses a Virtual IP (VIP) for database access. The VIP must be on the same subnet as the public IP address. The VIP is used for RAC failover (TAF). This will move to surviving node. Virtual address will be configured in hosts file of all nodes in a RAC. Regards,Pradeep. V

  • RELEVANCY SCORE 2.95

    DB:2.95:Error Opening Virtual Machine 16: The Host Name Could Not Be Resolved 89



    i`m trying to access the vmware server via http-proxy.

    while the webui seems to work , but when i open a console, the remote-plugin window pops up and tells "error opening virtual machine 16: the host name could not be resolved".

    so it looks the webui itself is proxy capable, but the remote-plugin is not !?

    DB:2.95:Error Opening Virtual Machine 16: The Host Name Could Not Be Resolved 89

    I had exactly the same problem. I didn't specify the FQDN because I didn't enter one when installing the host machine (Windows Server 2008), since it's set-up as a "pure" stand-alone machine.

    I was able to resolve the issue by starting WebAccess with localhost instead of the actual host name. Now, when accessing the console from WebAccess, it starts up correctly.

  • RELEVANCY SCORE 2.95

    DB:2.95:Finding Name Of The Physical Host Machine Name From Within A Virtual Machine 1x


    Hi, If I am logged onto a virtual machine, Can you please tell me if there is a way to find out the name of the physical host from within the logged in virtual machine itself? Thanks, KC

    DB:2.95:Finding Name Of The Physical Host Machine Name From Within A Virtual Machine 1x

    @BrianEh - You should read my blog more often :-)
    http://blogs.msdn.com/b/virtual_pc_guy/archive/2011/01/07/what-physical-computer-am-i-on.aspx

    Cheers,
    Benjamin Armstrong
    ============================
    Windows Virtualization
    Senior Lead Program Manager

    This posting is provided AS IS with no warranties, and confers no rights. You assume all risk for your use.

  • RELEVANCY SCORE 2.95

    DB:2.95:Problem With The Vmware Console Plugin In Ie On Vista. cc


    While installing the plugin to view the console, I get the attached error. The test reads as follows:

    Cannot view virtual machine console.

    The VMware Virtual Machine Remote Console plug-in failed to connect to your virtual machine.

    The remote host certificate has these problems:* The host name used for the connection does not match the subject name on the host certificate

    |

    DB:2.95:Problem With The Vmware Console Plugin In Ie On Vista. cc

    I'm having this same problem. Firefox and IE6 on XP.

    I have tried re-installing and even creating my own certificates using the docs at http://www.vmware.com/pdf/vi_vcserver_certificates.pdf

    No luck with any of it. I'm getting a new Linux box tomorrow, so I figure I'll give it a shot there.

  • RELEVANCY SCORE 2.94

    DB:2.94:Suse9.0 Host/Win2k Guest/Can't Sync To Virtual Disk 1j



    Hi,

    I just set up a Win2K Guest on a Suse Linux 9.0 Host. After installing MS Project I got an error message like "Can't sync to virtual disk". After I clicked ok, the virtual machine (Win2K) crashed and ever since I can't boot the Win2K machine anymore? What can I do?

    thanks tom

    DB:2.94:Suse9.0 Host/Win2k Guest/Can't Sync To Virtual Disk 1j


    Hi,

    I just set up a Win2K Guest on a Suse Linux 9.0 Host. After installing MS Project I got an error message like "Can't sync to virtual disk". After I clicked ok, the virtual machine (Win2K) crashed and ever since I can't boot the Win2K machine anymore? What can I do?

    thanks tom

  • RELEVANCY SCORE 2.93

    DB:2.93:Cannot See The Console From The Vm m9


    hello,

    i installed vmware server 2 beta and started a virtual machine. after starting the virtual machine in the internet explorer and i will click "open console in a new window", a new windows pops up, but theres a error message

    "Error opening the remote virtual machine test:8333\32: The host name could not be resolved"

    The dns system is still running and works fine. Is there any configuration i can make to see the console to install my OS ?

    kind regards

    Marco

  • RELEVANCY SCORE 2.92

    DB:2.92:Console Connection Failed fp



    Hello,

    i'm posting a new problem i've encountered today : when go to the web UI by entering the host name of the server (e.g. VMWSERVER, everything works fine until I try to open a console. The addon (i use firefox) raises an error :

    "Error opening the remote virtual machine VMWSERVER:8333\80:

    The host name could not be resolved.",

    and then the navigator crashes.

    I'm running Windows XP x64 (host) and it fails on each computer (client) I have, even on the host itself.

    Am i doing something wrong, or is it a bug to correct ?

    DB:2.92:Console Connection Failed fp


    I was receiving the same error when attempting to connect to my consoles using "localhost". I'm running Vista 64bit and VMware Server 2.0. I connect to the server home page and vm consoles using both my machine name and "localhost". I only recently figured out how to get the localhost address to work. When I pinged "localhost" I got back:

    Reply from ::1: timelt;1ms

    I checked the %windir%\system32\drivers\etc\host file and found the followng:

    127.0.0.1 localhost ::1 localhost

    For me, removing the IPv6 entry (that's the ::1 line) allowed the console to properly connect. Seems that the plug-in doesn't properly handle IPv6 addresses. Looks like you were using your machine name. My host file did not have an entry for my machine name, it was using the standard network DNS to resolve the ip address. In my case I run VMware Server on a laptop for development and often need to run my virtual machines without being connected to a wired or wireless network. I started by adding my machine name and 127.0.0.1 to my host file and eventually figured out how to get localhost to work.

    This worked for me because I was connecting to a local instance of the VMware Server. If your connecting to a remote instance then you may be getting a real DNS resolution error. I'm not too familar with IPv6 addessing since we don't use it on our networks. If you network is using IPv6 addesses, it would seem that VMware would need to update the console Plug-In to support IPv6 to correct the problem.

    I saw this question while searching for a resolution to my own console connection error, and figured I'd post what I found here.

  • RELEVANCY SCORE 2.91

    DB:2.91:General Access Denied Error (0x80070005), When Export Vm From Server2008 Host To Server 2008 Host 38


     
    Hi,
    I have VM, its name VMserver2008_Two, on host VMS2008_Test1. I have tried to migrate VMserver2008_two to another host, VMS2008_Test2. But it failed with this message: 'Export failed for virtual machine 'VMServer2008_Two' with error 'General access denied error' (0x80070005).
    Both host is Server 2008 with Hyper-V RC1 and same domain. And I did this as domain administrator.
    Here are steps I did:
    - Turn off VMServer2008_Two
    - Right click on VMServer2008_Two and choose Export
    - At Export Path, I browse to another host: \\VMS2008_Test2\c$
    - Then hit Export tab
    - After that I got that message.
     
    Please help me and let me know what I did wrong.
    Thanks
     

    DB:2.91:General Access Denied Error (0x80070005), When Export Vm From Server2008 Host To Server 2008 Host 38


    Hey folks, please be aware that As of 8/22/2008 this forum is de-comissioned, and there's pretty much nobody minding this particular MSDN forum..  all the virtualization support is over in the technet form
     
    http://forums.technet.microsoft.com/en-US/winserverhyperv/threads/
     
    (note the pinned message at the top of the forum that they are de-commissioning these on the 22nd  )
     
    Further discussion of this issue should be moved to the technet virtulization forum.
     

  • RELEVANCY SCORE 2.91

    DB:2.91:Error 401 - Repair Or Remove Virtual Machine Gives Error: Virtual Machine Is Is Not Associated With This Virtual Machine Manager Server. f9


    Background:
    Windows Server 2008 R2, SQL for VMM 2008 R2 is on another server.
    Issue: Upon trying to create a VM in the Library it fails, retry results in continued error, as does repair.
    Error is:
    Error (401) Virtual Machine host is not associated with this Virtual Machine Manager Server
    Recommended Action: Check the virtual Machine host name and then try the operation again. (Useless)
    Command: Repair-Vm
    Command: Remove-VM
    Both Commands give the same error, and the Event Viewer lgos (even the Hyper-V ones) show now errors.
    Steps Taken:
    1. Multiple Restart and Retry and Delete Fail
    2. Deleted the Source, and it still thinsk it is there even after a reboot.
    3. HYper-V has a VM with same name still present and functional.
    Any Ideas?David Baur

    DB:2.91:Error 401 - Repair Or Remove Virtual Machine Gives Error: Virtual Machine Is Is Not Associated With This Virtual Machine Manager Server. f9

    That didn't work, but in the posting you sent me to the fix was to go into the Database as it stated and update it it to a 1. The code was a 201, chanign this to 1 and then execute made it possible to delete the invalid VM. Many Thanks!
    http://social.technet.microsoft.com/Forums/en-US/virtualmachinemanager/thread/872034ba-3545-4431-b9f6-07ee8c65188bDavid Baur

  • RELEVANCY SCORE 2.90

    DB:2.90:I Cannot Use Console Plugin Due To Host Name pc


    I am running VMware Server 2 beta 2 on Windows Server 2003 x64.

    The host name of my server is v3 - it is a standalone server and not joined to a domain.

    I am using IP v4

    If I access VMware using http://v3:8222 I am able to access pages to configure VMs etc. but if I want to access the remote console I get a message:

    Error opening the remote virtual machine: v3:8333\32:

    The host name could not be resolved.

    I am able to use the v3 name elsewhere, so why does the browser plugin for remote console have difficulty using it ?

    If I access VMware using http://10.100.0.102:8222 then I am able to use the remote console without any issues.

    Any ideas ?

    Thanks,

    Tim

    DB:2.90:I Cannot Use Console Plugin Due To Host Name pc


    Hello,

    what kind of Server - Windows - edit in c:\Windows\system32\drivers\etc\hosts

    Put your ip and your hostname inside, not localhost!

    Same on Linux but there in the /etc/host file.

  • RELEVANCY SCORE 2.89

    DB:2.89:Vmware Tools Fail To Install On Win 98 Guest fk



    Host OS is Windows XP SP1. I just installed VMware V4.5.2, created the Windows 98 Virtual Machine and performed the Windows 98 SE install. All went without a hitch. Now I selected the install VMtools and soon after it begins I receive a "Windows Installer Error!" popup. It says "Error opening installation log file. Verify that the specified log file location exists and is writable." There is nothing that tells me the specified log file location or it's name. Now I'm stumped where to go next. Can anyone help?

    Thanks in advanced!!

    Don Dayton

    ddayton@intlsteel.com

    DB:2.89:Vmware Tools Fail To Install On Win 98 Guest fk


    See if this helps:

    1: Verify that you are logged on with a user in win98

    2: verify that %temp% (by default C:\WINDOWS\TEMP) is writable

    3: Update your msi install engine http://www.microsoft.com/downloads/details.aspx?displaylang=enFamilyID=CEBBACD8-C094-4255-B702-DE3BB768148F#filelist

    Good luck.

  • RELEVANCY SCORE 2.89

    DB:2.89:Cannot Power Vm After Crash jp



    After crashing the host i cannot power on my VM.

    Error message:

    Unable to change virtual machine power state: The process exited with an error:

    Unable to fix standard file descriptors.

    End of error message.

    My host runs on SLAMD64 (64bit slackware), the guest os is slackware

    Please help!

    DB:2.89:Cannot Power Vm After Crash jp


    If the VMDK itself is ok then create a new VM and point it to the existing VMDK.

    If you had snapshots there's a bit more to do.

  • RELEVANCY SCORE 2.89

    DB:2.89:Error Opening The Remote Virtual Machine... cf



    Hi,

    I've seen this raised few times on this board, but I'm not sure if I have a similar setup to others who have had the same issue.

    I've recently installed server 2.0 RC2 (build 110949) on a windows vista 64-bit host. Clean install of the OS and this VMware release.

    In the process of setting up a new virtual machine, after installing the remote console plugin and trying to view the console of the new VM, I get the following error message:

    Error opening the remote virtual machine localhost:8333\32:

    The host name could not be resolved

    I did have RC1 working on vista 64-bit, unfortunately I can't re-create as I had to blitz the initial vista install with RC1 on it.

    https://localhost:8333/ui/ is referenced in the main vmware server shortcut (rather than using the FQN)

    I've tried setting the FQDN in the hostfile, but this doesn't appear to have resolved it

    Any suggestions would be appreciated

    Update *****

    Using the IP address https://xxx.xxx.xxx.xxx:8333/ui/ does work but when you use this specifically in IE7,you get a prompt to choose a digital cert.. but there is no digital cert listed!

    You can just click on OK and you get brought to the IE7 warning screen (there is a problem with this website's security certificate), then you can proceed

    DB:2.89:Error Opening The Remote Virtual Machine... cf

    Just a thought... I wonder could the network metrics that vista gives the network interfaces be some part of the issue? On testing we did with the cisco vpn client on the 32-bit version of vista, we found had to change the metric of the lan card to adjust the priority, in order to get the VPN traffic to work.

    I know very little about the new network setup with vista (as there are differences when compared to the IP configuration on 2003 or xp).

    Is this a possibility?

  • RELEVANCY SCORE 2.88

    DB:2.88:Error When Opening Virtual Machine k1



    Hi,

    DB:2.88:Error When Opening Virtual Machine k1


    I had this problem when I was closing guests os and the power went off, I guess the vmx file get damaged, so maybe You have to try a fresh copy?

    ____________________________________

    VM or Not to VM...?

    That is the question!

  • RELEVANCY SCORE 2.88

    DB:2.88:I Get The Error Build Agent Is Not Installed How To Get Rid Of This Error ? 9s


    HiI have the following installed on a single machine Server ( TFS + controller + agents +SCVMM + Build service host configured) - all in one pc for testing ( 2010 Beta 2 components ) - 64 bit - win 2008 HPC edition Client xp  32 bit – VSTS IDE , MTLM test elements,  installed lab and test agent
    Virtual machine ( TESTVM )- Initially did not have lab and test agent - created a virtual environment with one PC – windows 2008 - Testing capability and workflow capability was disabled - then installed lab agent and test agent - Testing capability is enabled workflow capability was disabled and throws an exception displayed =================Error Message ================ Environment message: Type=Error; Message=TF266044: One or more machines are not ready to run workflows. For more information, see the individual machine errors.;
    Machine messages:
    Machine name: Machine4
    Machine message: Type=Error; Message=TF266054: Build agent is either not installed or not configured on the machine. Install and configure Visual Studio Team Foundation Build Service Host on the machine and try the operation again.;============================================
    Where Do I locate Build Agent ? Visual Studio Team Foundation Build Service Host is already configured under admin credentials in the serverbox. How should I resolve this issue.
     

    DB:2.88:I Get The Error Build Agent Is Not Installed How To Get Rid Of This Error ? 9s

    Hi Pramod, Here are the answers to your questions:MTLM is invoked from my XP client m/c My environment has only one virtual m/c ( Win 2008 server) (Role - Web Server)my test settings I see two m/cs ( Local and Webserver) Local having a green tick mark Few questions on this 1. Local PC is visible here in the test settings, it does help capturing actions recording and its related settings is this the reason ? Does that mean Local PC will be attached to any environment that we create ?'Local' role signifies the machine on which you launch MTLM and from where you start your testing. In your case, it is your XP client machine.The reason for this is that you'll have the browser or rich client open on your client machine. So, it allows you to define what all data you want to collect from your client while you run the test manually.2. Local m/c icon in test settings is having a green tick mark (right top corner) - what does this signify ?The green tick mark signifies that this is the machine from where tests will be run. Actually, it makes sense in case of automated tests where you can choose the machine on which you want to run the tests - by using this green tick mark. In case of manual tests, it is always the Local machine where MTLM is run.3. If i take a snapshot for a defect , the snapshot of the environment is taken successfully but it has only the snapshot of virtual PC does that mean that we wont be able to take the snapshot of this combination of physical and virtual env if my manual tests run on physical m/c?No. We can only take snapshots of the virtual machines that are a part of virtual environment in the lab and we cannot snapshot physical machines. We wish we could. :)4. In continuation of the previous question, If we need to have snapshot of the client too then does it have to be part of the env, also MTLM should be installed in that VM box i.e. we have to do the testing using the VM's MTLM which is viewed inside the physical m/c's MTLM's env viewer ?Go to Physical m/c - MTLM env viewer - VM m/c's MTLM ( do manual testing here )  Is my understanding right here ?Yes. You got it absolutely right.5. Build agent will be installed on the computers on which automatic deployment is required, is this right ? For example - if my env contains  Web server + DB server + 3 clients and mine is web application.                        considering I have installation activity in both and web and DB server then build agent should be installed in web and DB only ?You are right. But, from the MTLM UI, when you enable 'Run workflows' capability for an environment, we expect you to install build agents on all machines in the environment and for them to turn ready. So, if you do the above scenario, you will get an error from MTLM that says 'Build agent is not installed' on the 3 client machines. If you are using the lab workflow for your application deployment, this will not run unless the error is resolved. So you will be blocked from running the deployment workflow. Two ways to get around this:a. (Recommended) Install build agents on the client VMs too to make the environment status 'Ready' (though technically it should not be required).b. If you really dont want to install build agents there, customize the deployment workflow, to remove the check for environment to ready, and make the check only for web and DB server instead.We'll take this feedback for the future release, and try to make the scenario work like you described.

  • RELEVANCY SCORE 2.88

    DB:2.88:Error While Opening The Virtual Machine: File Not Found j9



    I would like to automatically start my virtual machine on reboot of the host. I'm running Windows XP Professional 5.1.2600 SP3 as the host system, CentOS is the guest. I'm running version 5.0.0 build-812388 of vmplayer.

    I've created a shortcut link in my startup folder and modified the target to "C:\Program Files\VMware\VMware Player\vmplayer.exe" I:\Documents and Settings\APB.XP80GB\My Documents\My Virtual Machines\Elastix\Elastix.vmx but that gives the error above.

    What is the proper way to do this please?

    Thank you in advance.

    DB:2.88:Error While Opening The Virtual Machine: File Not Found j9


    I would like to automatically start my virtual machine on reboot of the host. I'm running Windows XP Professional 5.1.2600 SP3 as the host system, CentOS is the guest. I'm running version 5.0.0 build-812388 of vmplayer.

    I've created a shortcut link in my startup folder and modified the target to "C:\Program Files\VMware\VMware Player\vmplayer.exe" I:\Documents and Settings\APB.XP80GB\My Documents\My Virtual Machines\Elastix\Elastix.vmx but that gives the error above.

    What is the proper way to do this please?

    Thank you in advance.

  • RELEVANCY SCORE 2.88

    DB:2.88:Failure While Opening Vm Causing Errors In Later Operations With Other Vms On Same Host 7z


    Hi!

    I'm having some problems related to opening several virtual machines running on the same VMware host (Server) in sequence. If opening one of the VMs fails (for example because of invalid VMX path), succeeding open operations on the same VMware host will fail as well (even though they are correct). If I ignore the failures and proceed operation on the successfully opened VMs, some succeeding operations on the already open VMs will fail. This is at least the case for RevertToSnapshot, but possibly other as well (haven't done too much testing, but it appears that file copying and execution works).

    The sequence of errors produced is:

    VMware host handle: 62: Opening virtual machine failed. Error code: 4. Textual description: A file was not found - Invalid VMX path.

    VMware host handle: 62: Opening virtual machine failed. Error code: 3008. Textual description: Cannot connect to the virtual machine - Correct VMX path (should work).

    I'm using the vix.dll C library, file version 1.0.3.44621.

    Best regards,

    J

    DB:2.88:Failure While Opening Vm Causing Errors In Later Operations With Other Vms On Same Host 7z


    Yikes. Haven't seen that one. Have you tried reconnecting to the host after the first failure? A horrible (but still do-able) workaround would be to reconnect to the host in the event of such an error.

  • RELEVANCY SCORE 2.88

    DB:2.88:Cannot Open Guest Console In Webui (Windows Srv2k3/Ie7) ma


    Hello,

    We upgraded to Beta 2 on 2 Win2K3 Srv SP2 and we cannot open any guest console under WebUI.

    The error message is:

    "Error opening the remote virtual machine host:8333\96:

    The host name could not be resolved."

    Where "host" in "host:8333\96:" is the NetBIOS name of the Host (Srv2K3).

    Any idea?

    I don't understand the "\" in what seems to be an URL...?

    Thanks

    DB:2.88:Cannot Open Guest Console In Webui (Windows Srv2k3/Ie7) ma


    If you upgrade to RC1, it should no longer be necessary to edit your system's hosts file or do anything special.

  • RELEVANCY SCORE 2.88

    DB:2.88:Not Enough Physical Memory pk



    I am getting an error message when trying to open a second VM on my machine, which has recently been upgraded from 1GB to 2GB of RAM. Both VMs have 250MB of RAM assigned to them so the 2GB should be more than enough.

    Does anyone have any suggestions?

    The message i'm getting is:

    Not enough physical memory is available to power on this virtual machine.

    To fix this problem, power off other virtual machines, decrease the memory size of this virtual machine to 172MB, increase the amount of physical memory for all virtual machines to 297MB, or adjust the additonal memory settings to allow more virtual machine memory to be swapped.

    If you were able to power on this virtual machine on this host computer in the past, try rebooting the host computer. Rebooting may allow you to use slightly more host memory to run vistual machines.

    DB:2.88:Not Enough Physical Memory pk


    What is your host OS?

    What version of GSX?

    Post the vmware.log file from this VM that fails to power on

  • RELEVANCY SCORE 2.88

    DB:2.88:Unable To Update Syslog Host Name On Esxi5 Host Machine mf



    Hello All,

    I am unable to update the SysLog host name via the following method on one particular ESXi 5 host machine:

    From vSphere Client version 5.0.0, go to Configuration - Software - Advanced Settings - Expand 'Syslog' and select 'Global', enter host name such as udp://server-name:514, and hit OK. When I do, vSphere Client thinks for about a minute and I get the following error message:

    Call "OptionManager.UpdateValues" for object "EsxHostAdvSettings-54" on vCenter Server "server-name" failed.

    From the client recent tasks information, I get:

    Update option values, 172.22.216.6, A general system error occurred: Internal error Administrator "server-name"11/29/2011 1:04:50 PM11/29/2011 1:04:50 PM11/29/2011 1:05:31 PM

    Please note I have updated the FQDN of the server with "server-name" above. I am using the SysLog collector which comes with the ESXi install media.

    I have done this on 30+ other host machines in the same datacenter, all servers are new/default installations. I have not been able to discover any difference with this host vs. the 30+ other host machines which have no issues. There are no virtual machines on this host machine yet. I have already rebooted the host machine as well, and restarted vSphere client multiple times. The only thing I have not done is reboot the vCenter Server, which I will do eventually. Again, though, it works on 30+ other host machines without issue.

    Any ideas? What else can I give you to help discover the root cause and ultimately a fix?

    Thanks!

    Gary

    DB:2.88:Unable To Update Syslog Host Name On Esxi5 Host Machine mf


    FYI, we ran into this issue. It was discovered the DNS client was disabled. The issue went away once we enabled it.

  • RELEVANCY SCORE 2.87

    DB:2.87:Problem To Connect To The Virtual Machine Console Through The Scvmm Admin Console x1


    Hello!
     
    I have a problem to connect to the virtual machine console through the SCVMM Admin Console from a machine running Windows Xp. The machine/user is in the same domain as the VMM server and i can see all the host/virtual machines etc.
     
    But when i right click a virtual machine and selec connect to virtual machine I get this error message:
     
    Cannot connect to virtual machine VMtest because the the virtual guest services feature is not available.
    Install the Virtual Guest Service on the virtual machine. If the Virtual Guest Services already is installed, ensure that the component has not been disabled.
     
    ID: 1736When i use  SCVMM Admin Console from the VMM server it works.Any ideas?

    DB:2.87:Problem To Connect To The Virtual Machine Console Through The Scvmm Admin Console x1

    Hello, Have you try to disable firewall on both side to exclude a FW issue ? Ced.

  • RELEVANCY SCORE 2.87

    DB:2.87:Error Opening The Remote Virtual Machine ks


    Hi All,

    When i'm trying to open remote console ( double click in console screen) I'm geting error: "Error opening the remote virtual machine lt;machine namegt;. The host name could not be resolved.". Any workaround?

    Thanks.

    DB:2.87:Error Opening The Remote Virtual Machine ks

    Hi All,

    When i'm trying to open remote console ( double click in console screen) I'm geting error: "Error opening the remote virtual machine lt;machine namegt;. The host name could not be resolved.". Any workaround?

    Thanks.

  • RELEVANCY SCORE 2.87

    DB:2.87:"Unexplained Error" When I Have No Wireless Connection 8c


    I have been using a Linux (Ubuntu) Virtual Server running inside a Windows XP Host on my laptop.

    It has been working fine for a month or so.

    Today for the first time I tried to use it away from home. The server appears to start OK but when I try to open the remote console I get the following message:

    +Error opening the remote virtual machine george_laptop:8333\16: +

    +* An unexplained error occured.*+

    I turned off the wireless connection at home and got the same problem.

    The network configuration is "NAT" sharing network connections etc.

    Why is this happening surely I should still be able to run the virtual server?

    Cheers

    George

    DB:2.87:"Unexplained Error" When I Have No Wireless Connection 8c

    In virtual machine, add a virtual network interface of type "HostOnly".

    This way, you'll ensure comunication between host and guest regardless

    of the phisical network connection state.

    Then, make sure that at least one of your phisical network

    interfaces has a static IP address (i.e. not assigned by DHCP),

    otherwise you'll get the error message.

    This way it worked for me.

  • RELEVANCY SCORE 2.86

    DB:2.86:Error Message When Connecting To Vm From Vmm - Virtual Machine Manager Failed To Connect To The Virtual Machine Because The Host Name () Could Not Be Resolved By The Domain Name System 3c


    Running Virtual Machine Manager and 2 Windows Server 2008 servers running Hyper-V.. From the console of the server running the virtual machine I can connect to the VM just fine. From the VM running Virtual Machine Manager (on a VM) I can connect just fine. On my workstation running the Virtual Machine Manager I get an error when I try to connect Virtual Machine Manager failed to connect to the virtual machine because the host name () could not be resolved by the Domain Name System.I can however connect to a different VM on a different machine from my same workstation.I have searched google, and the MSKB on this error and came up with nothing.Tried to install VMM console on another workstation and I get the same results.

    DB:2.86:Error Message When Connecting To Vm From Vmm - Virtual Machine Manager Failed To Connect To The Virtual Machine Because The Host Name () Could Not Be Resolved By The Domain Name System 3c

    Finally got a resolution, I was running the VMM console from an XP Sp2 machine, upgraded the SP3 and the error changed to a dialog box pointing me to 

    http://support.microsoft.com/kb/322756/The resolution is -

    Click Start,
    click Run,
    type regedit, and then press ENTER.In the navigation pane, locate and then click the
    following registry subkey:

    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Lsa

    In the details pane, right-click Security Packages,
    and then click Modify.In the Value
    data box, type tspkg. Leave
    any data that is specific to other SSPs, and then click OK.In the navigation pane, locate and then click the
    following registry subkey:

    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\SecurityProviders

    In the details pane, right-click SecurityProviders, and
    then click Modify.In the Value
    data box, type credssp.dll.
    Leave any data that is specific to other SSPs, and then click OK.Exit Registry Editor.Restart the computer.

  • RELEVANCY SCORE 2.86

    DB:2.86:Vmware Player Unrecoverable Error: (Vmx) 2 19



    Hi everybody,

    I got a crash when opening a virtual machine.

    Here are the details:

    - host= windiws XP w/ SP 3

    - guest = windows servers 2003 on an external drive usb 2.0

    I got this error:

    VMware Player unrecoverable error: (vmx)

    DB:2.86:Vmware Player Unrecoverable Error: (Vmx) 2 19


    Hi everybody,

    I got a crash when opening a virtual machine.

    Here are the details:

    - host= windiws XP w/ SP 3

    - guest = windows servers 2003 on an external drive usb 2.0

    I got this error:

    VMware Player unrecoverable error: (vmx)

  • RELEVANCY SCORE 2.86

    DB:2.86:Maximum Length Of Virtual Machine Host Name ms


    Hi,

    Is there any limitation of virtual machine host name of ESX 3.0 or ESX 3.5?

    GMR

    DB:2.86:Maximum Length Of Virtual Machine Host Name ms

    Try avoiding special caharcters in the names as this can cause problems.

    Regards

    Anil

    Save the planet, Go Green

    if you found my answer to be useful, feel free to mark it as Helpful or Correct.

  • RELEVANCY SCORE 2.86

    DB:2.86:Error At 99% ck



    hello,

    i will convert a windowx xp pc to a virtual machine at an esx 3.0.2 host.

    at 99% i beome an error?

    Message

    Task failed: P2VError UNKNOWN_METHOD_FAULT(sysimage.fault.ReconfigFault)

    So whats wrong?

    DB:2.86:Error At 99% ck


    Hello

    RAM = 256

    Disk = 5 GB / 72 GB Free

    OS = windows xp sp1

    destination = esx 3.0.2

    error message image fault

  • RELEVANCY SCORE 2.86

    DB:2.86:Unable To Connect To Scvmm Server On Create Snapshot From Lab Center fm


    We recently added a second SCVMM host so that we could have additional VMs. Prior to that everything worked well. Now we are unable to create new snapshots from within Lab Center. The error is:
    Environment message: Type=Error; Message=TF259098: Team Foundation Server could not perform the following operation because of errors on one or more virtual machines: Create snapshot. Resolve those errors, and then try the operation again.;
    Machine message: Type=Error; Message=TF260078: Team Foundation Server could not connect to the System Center Virtual Machine Manager Server: TF260038: Team Foundation Server is initializing connection to the System Center Virtual Machine Manager Server:
    Scvmm server name. Please try the operation after some time.. More information for administrator: TF260078: Team Foundation Server could not connect to the System Center Virtual Machine Manager Server: Scvmm server name. More information
    for administrator: TF260038: Team Foundation Server is initializing connection to the System Center Virtual Machine Manager Server: Scvmm server name. Please try the operation after some time.
    I've tried reprovisioning everythingandit alllooks good using the TFS Admin console. I can create snapshots directly using Hyper-V Manager directly on the SCVMM machine. Any ideas what would prevent this communication/ creating
    snapshots from Lab Center?

    DB:2.86:Unable To Connect To Scvmm Server On Create Snapshot From Lab Center fm

    I encountered the same problem and solved by restarting everything (restart TFS server, SCVMM server...)
    don't understand why this could happen...totta wang

  • RELEVANCY SCORE 2.85

    DB:2.85:Error Opening The Remote Virtual Machine... 13


    Hello all. I installed VMWare 2.0 build 84185 a few months ago. It worked fine until today. Now when I launch the virtual machine, it begins to power up then I get the following error:

    Error opening the remote virtual machine localhost:8333\32:

    VmodlVmomiFaultSystemError error.

    I can't think of anything specific that I've changed since the last time I used it other than standard Windows Updates and Java. VMWare uses its own jvm.dll file so I don't know if the Java update caused it. Both the host and remote OS are Win XP Pro SP3. Any help would be greatly appreciated.

    DB:2.85:Error Opening The Remote Virtual Machine... 13

    Yes, the upgrade fixed it. You'd think the console would just say that instead. Thank you!

  • RELEVANCY SCORE 2.85

    DB:2.85:This Cpu Is Vt-Capable But Vt Is Not Enabled za



    Hello - I'm getting this error message when trying to instal a 64bit XP virtual machine.

    I have enabled VT in the bios of the host yet I still get this error when trying to start the virtual machine:

    This CPU is VT-Capable but VT is not enabled. You have configured this virtual machine as a 64-bit guest operating system. However, this host's CPU is not capable of running 64bit virtual machines or this virtual machine has 64-bit supporrt disabled.

    DB:2.85:This Cpu Is Vt-Capable But Vt Is Not Enabled za


    The vt.iso image only checks for VT, which is an Intel offering. It does not check for AMD's hardware-virtualization offering, which is AMD-V.

  • RELEVANCY SCORE 2.85

    DB:2.85:Virtual Office 2003 And Non-Virtual Office 2010 On Windows 7 Machine, Error Opening Outlook 2003 z3



    Hi, we have need to use office 2003 virtualized on windows 7 machine, which has office 2010 installed. But when opening virtual outlook 2003, I get message "Unable to open your default e-mail folders. Your profile is not configured."

    I tried to use writecopy isolation and followed this Blog About Thinapping Office 2003 but no success. Anyone had the same problem?

    DB:2.85:Virtual Office 2003 And Non-Virtual Office 2010 On Windows 7 Machine, Error Opening Outlook 2003 z3


    Hmm... managed to get Outlook 2003 working when starting it first with clean profile. But when opening 2010 version first the virtualized outlook gives the error. Plaaarghh...

  • RELEVANCY SCORE 2.85

    DB:2.85:Hyper-V Migration Problems zc


    I have the following server setup:

    -Storage Server, with an SMB file share
    -hyper-v host 1
    -hyper-v host 2

    All three servers are in the same domain, and the VMs are hosted on the host servers but stored on the storage server. When I try to move a VM from one host to the other I get the following error message:

    Virtual machine migration operation failed at migration source.

    Failed to establish a connection with host 'host 2': No credentials are available in the security package (0x8009030E).

    The Virtual Machine Management Service failed to authenticate the connection for a Virtual Machine migration at the source host: no suitable credentials available. Make sure the operation is initiated on the source host of the migration, or the source host
    is configured to use Kerberos for the authentication of migration connections and Constrained Delegation is enabled for the host in Active Directory.

    [Expanded Information]
    Virtual machine migration operation for 'VM' failed at migration source 'host 1'. (Virtual machine ID .....)

    The Virtual Machine Management Service failed to establish a connection for a Virtual Machine migration with host 'host 2': No credentials are available in the security package (0x8009030E).

    Failed to authenticate the connection at the source host: no suitable credentials available.

    All the servers already have constrained delegation enabled, with use kerberos only checked

    Does anyone know what the problem is here?

    Thanks

    DB:2.85:Hyper-V Migration Problems zc

    On first glance, it looks like a constrained delegation problem. You could try out a couple of things - (1) Check if the migration is successful if you initiate the operation *on* the same server (eg: From failover cluster manager on host2 in your case)
    on which the VM is running or (2) Go thro' Taylor's blog on constrained delegation

    http://blogs.msdn.com/b/taylorb/archive/2012/03/20/enabling-hyper-v-remote-management-configuring-constrained-delegation-for-smb-and-highly-available-smb.aspx
    Regards
    Praveen

  • RELEVANCY SCORE 2.85

    DB:2.85:Error Opening Virtual Machine cf



    When I create a virtual machine I am unable to open it and the following error message is displayed:-

    Error opening virtual machine "/var/lib/vmware/Virtual Machines/Windows XP Professional/Windows XP Professional.vmx": Virtual machine "/var/lib/vmware/Virtual Machines/Windows XP Professional/Windows XP Professional.vmx" is not in the inventory.

    This message then occurs each time I try to open the machine I just created and I am unable to open it.

    The permissions on that folder are correct. I am unsure of what to do next.

    Thanks in advance.

    DB:2.85:Error Opening Virtual Machine cf


    Don't worry, I just restarted vmware-console and it worked.

    Thanks anyway.

  • RELEVANCY SCORE 2.85

    DB:2.85:Imgcustdisk: Open Description: Could Not Create Vmount2locator Object ac



    I'm currently running ESX Server 2.1 and Virtual Center 1.0.1 Build 7770

    We've been getting the following error for the last couple of months whenever we try and deploy a new virtual machine in the Virtual Center software.

    We create a new Server VM from the standard build image and then complete the customisation wizard. The Virtual Center software then starts deploying the VM to the selected Host server. Right at the end of the deployment, it fails with the error message:

    ImgCustDisk: Open Description: Could not create Vmount2Locator object Context: Opening disk file

    /vmfs/VMFS020/TEST20_01_5017e7e1-546b-ca85-9681-1ad6de029559.vmdk@xxxxxx:32775

    If you do not use the customisation wizard than the VM deploys OK, you then just have more work to do once the New VM server has been switched on. The error seems to occur regards of which VM host you chose to deploy the

    template to.

    DB:2.85:Imgcustdisk: Open Description: Could Not Create Vmount2locator Object ac


    To resurect an old thread, I just got this as well when deploying a server (after rebuilding a new VC server creating a new template from a server.) I have taken the Windows 2000 sysprep and put it under the 1.1 directory (with folder structure) and added the windows 2003 SP1 sysprep to the windows 2003 sysprep directory.

    VC 1.31, ESX 2.52, windows 2003 template....went all the way through and gave the error...

    Tried completing the deployment again and this time I received 2 errors in a row. One was unable to power off server and the next popup was failed to customize guest os while decrypting strings : \[pfxcrypt] error decrypting: .

    Message was edited by:

    Rumple

  • RELEVANCY SCORE 2.85

    DB:2.85:Vm Player Not Opening Any Virtual Machine cf


    Hi,

    I have installed VMware Player 3.1 . It was working fine for one day. The next day I tried to run it, it is not working. When I runit, its main widnow comesup (which has options of "Create a new Virtual machine", "Open a virtual machine" etc). but when I click on any virtual machine and ty to play it, it do not open it. It just stay on the same screen . It do not show any error also. It is not showing the Virtual machine settins screen also. I also tried to create a new virtual machine. It show the initial paramters screen where I can select operating system and configure hardware but after that it do the same. It stays on the same window and do not start machin neither show new virtual machine in left pane.

    My Host operating system is Win XP sp3.

    Please help.

    Regards

    Arban

    DB:2.85:Vm Player Not Opening Any Virtual Machine cf

    Hello,

    Thanks for the quick reply.

    It was because of a firewall application which suddenly started giving me problems. My internet explorer also stops working. I remove fire wall and reinstall IE and then check VMWare player . Everything start working perfectly.

    Thanks

  • RELEVANCY SCORE 2.85

    DB:2.85:Cannot Logon To Vm Using Domain Account d1


    I created a new Virtual PC on my new Windows 7 64bit host machine.
    I created it using an existing VHD. The VHD was previously running on my Windows XP Pro machine under Virtual Server 2005 R2with Windows Server 2003 R2.
    The Virtual Server is a member of my company domain. Under VS2005, I could start the Virtual Server and logon, and,if necessary, I could use the option in the logon dialog to Log on using dial-up connection. I could use a VPN connection configured
    in the virtual server.
    After copying the VHD to the Windows 7 host, and opening it with Windows Virtual PC, I was able to logon to the Virtual Machine using a domain logon, and it connected, no problem.
    This may or may not be relevant to my problem, but the host machine crashed last night with the Virtual Machine was running. When I restarted the host this morning, and then restarted the VM, I cannot logon using my domain account. I get the logon message
    The system cannot log you on due to the following error: The specified domain either does not exist or could not be contacted. Please try again or consult your system administrator.
    Under Windows Virtual PC, the Virtual Machine logon does not offer the option to logon with dial-up connection.
    I created a VPN connection on the host machine, and I tried to logon on the VM with the host VPN connection open, but that made no difference.
    I can logon to the VM using a local account, but I need to be able to logon using my domain login.
    Thanking you in advance for your help.

    DB:2.85:Cannot Logon To Vm Using Domain Account d1

    I think I've figured out why the logon no longer offers the option to use dial-up networking - installing the WPC Integration Features.
    I moved another VHD that I was using in a virtual server in Virtual Server 2005 as the system VHD in Windows 7 Virtual PC. I noticed that the logon offered the option to use dial-up networking, but that option disappeared after installing the Integration
    Features.
    My work around is to log on the to machine locally using the Windows Virtual PC window and connect to the company network using the Windows VPN client. Then, I connect to the Virtual Machine using a Remote Desktop Connection, logging in with my domain credentials.
    I actually prefer to use RDP to work on the machine. I like the ablility to bring the hard disk resources of the host machine to the RDP session. I also like the behavior of RDP in full screen mode better than WPC because WPC requires you to login again
    when entering and leaving full screen. What's that about?
    All this will become irrevalent when I rebuild the host with Windows Server 2008 R2 and run Hyper-v. I may be able to move my old Virtual Server 2005 machines into Hyper-v, but I intend on creating new virtual machine anyway. I'm sure I'll run into challenging
    problems in that effort as well and will be combing the forums again soon.

  • RELEVANCY SCORE 2.84

    DB:2.84:Can Windows Virtual Pc Be Installed On Windows Embedded Standard 7 Host Machine ? sc


    Hello
    I have a host machine with Windows Embedded Standard 7 OS (x64). I tried to install Windows Virtual PC on it but the installation failed with error message The update is not applicable to your computer. I have tried the RegistrySizeLimit way
    but it did not work. However, Virtual PC 2007 could be installed on the host machine successfully. Is there any way I can try to install Windows Virtual PC on the host machine?
    Thanks

    DB:2.84:Can Windows Virtual Pc Be Installed On Windows Embedded Standard 7 Host Machine ? sc

    Hello
    I have a host machine with Windows Embedded Standard 7 OS (x64). I tried to install Windows Virtual PC on it but the installation failed with error message The update is not applicable to your computer. I have tried the RegistrySizeLimit way
    but it did not work. However, Virtual PC 2007 could be installed on the host machine successfully. Is there any way I can try to install Windows Virtual PC on the host machine?
    Thanks

  • RELEVANCY SCORE 2.84

    DB:2.84:Remote Console And Workgroups kj



    Error: Error opening the remote virtual machine machine_name: The host name could not be resolved.

    Config: VMWare Server 2.0 RC1 on Windows Server 2008 in its own workgroup with DHCP assigned IP address, accessed from a client PC in a different domain

    I'm aware of the resolution described in the release notes. However:

    - I can't use an IP address in the url or add it to the hosts file because it may change due to DHCP

    - Localhost is obviously not appropriate

    The only remaining option is fully qualified domain name. What is the FQDN for a server in a workgroup?

    Thanks in advance

    DB:2.84:Remote Console And Workgroups kj


    I worked around it by setting up an asp page that detects the ip address and constructs the url i.e.

    LT;a href="https://LT;%=Request.ServerVariables("LOCAL_ADDR")%GT;:8333" target="_blank"GT;VMWare ServerLT;/aGT;

  • RELEVANCY SCORE 2.84

    DB:2.84:If We Rename A Host Group, Can Existing Environment Be Updated To The Renamed Host Group Name? p1


    Hi,
    In SCVMM we rename the host group name.

    In the TFS Admin console, we add thethe new name host name to the TPC. We have not tried toremove the old one will this work yet, not sure of impact
    The existing enviroments are not available since they still indicate the old host group name
    (I have message Message= TF259037: Team Foundation Server has found that the virtual machine has migrated from the host group All Hosts\OldName to another host group or to the library. Contact your system administrator to move the virtual machine
    to the correct host group.
    In MTM, theenvironment still indicates the old host name. Anyway I can update that value? (edit the environment does not allow to change the host group name)
    What are the steps inContact your system administrator to move the virtual machine to the correct host group?
    Is the solution toCompose new environment in MTM (I would need to delete the environment associate to the old host name first)
    The following post (http://blogs.msdn.com/b/lab_management/archive/2010/07/02/visual-studio-lab-management-2010-host-group-and-library-management.aspx)
    indicate how it would automatically be update if I renamed in the same hierarchy. We did not do this, we did what is not recommended but does not offer a workaround.
    Thanks

  • RELEVANCY SCORE 2.84

    DB:2.84:Changing Host Name In 5.3 jz


    Hi,We have 2 instances of Content Server 5.3 running on the same machine. I am trying to change the host name from base host name to Virtual host name for one Content Server 5.3 Installation.I updated updated all the files that have the reference to host name. I am able to start the docbroker, the content server and even the Index server.But the Index Server Completeness test fails.WARNING: The FASTSEARCH environment variable, indicating the path to theroot directory of the FAST Data Search installation, was not set.Assuming '/.../..' is the correct path.Tue Sep 20 16:21:09 2005 [PROGRESS]: Completeness Test StartedTue Sep 20 16:21:20 2005 [PROGRESS]: Fetched all 4291 docids from DocumentumTue Sep 20 16:21:20 2005 [INFO ]: Get Documentum IDs: 8.790 sTue Sep 20 16:21:20 2005 [DEBUG ]: Got 4291 docids from DctmTue Sep 20 16:21:20 2005 [ERROR ]: Failed to retrieve number of searchable documents from FAST using the url: %s.Tue Sep 20 16:21:20 2005 [ERROR ]: http://host-name:20100/cgi-bin/asearch?hits=1offset=0query=meta.collection%3AdocumentumTue Sep 20 16:21:20 2005 [ERROR ]: Ensure that the host name "host-name" is pingable, FAST is running and that the port number "20100" isctTue Sep 20 16:21:20 2005 [FATAL ]: Also try opening the url above in a web browserTerminated.Could some body help.Thanks.

    DB:2.84:Changing Host Name In 5.3 jz

    The Index server is on the local host.I am able to bring up the Docbroker and docbase with the virtual host name.I am able to ping to that virtual host name as well.But I am not able to get that particular process (FAST) running.The base port number is 18000 and this particular process listens to 20100. I do not see that. "netstat -a|grep 20100" returns nothing.

  • RELEVANCY SCORE 2.84

    DB:2.84:Configuration File Cannot Be Found cs


    I run the New Virtual Machine Wizard to create a new virtual machine in Workstation 6.0.4. I specify a Typical machine configuration, with WinXP Pro as guest on Ubuntu. The name for the new virtual machine is WinXP at /home/ray/vmware/WinXP. I choose NAT networking. I have tried different disk sizes, with ample disk space available. For example, I specify 15GB, say "Allocate all disk space now," and turn off the option to "Split disk into 2 GB files."

    Every time, I get "Error opening virtual machine '/home/ray/vmware/WinXP/WinXP.vmx. The configuration file for this virtual machine cannot be found. It might be missing from the virtual machine directory, or the path specified to access this virtual machine might be incorrect." What's more, if I create the /home/ray/vmware/WinXP subdirectory before running the wizard, the wizard will delete that subdirectory at this point. Any ideas what's going on?

    DB:2.84:Configuration File Cannot Be Found cs


    Check the effective rights of your user in the directory where you want to create the guest.

  • RELEVANCY SCORE 2.84

    DB:2.84:The Host Name Could Not Be Resolved. 8d


    Hi, I'm now running VMWare Server, (Virtual Infrastructure Web Access), Version 2.0.0 beta build 84185.

    When I create a new VM machine and select Console. The "VMWare Remote Console" screen opens then the message "Error opening the remote virtual machine hp1:\8333\16: The Host name could not be resolved."

    Any ideas how I get round this. ?

    Its a new VM machine so without seeing the console I'm slightly stuck.

    DB:2.84:The Host Name Could Not Be Resolved. 8d

    I just added my machine's name to my hosts file next to localhost, e.g.:

    127.0.0.1 localhost moriarty

    Everything worked fine after that.

    I do think it's kinda lame that there's no way to change the host name after installation, though. This would be a nice, no NECESSARY, feature to have in the web UI.

  • RELEVANCY SCORE 2.83

    DB:2.83:Add Virtual Machine Host: Error (2912) - The Group Name Could Not Be Found (0x800708ac)) p8


    Hi,
    Windows Server 2008 x64, VMM 2008, no trust - only one domain.
     
    Add virtual machine host fails with the following message:
    Error (2912)
    An internal error has occurred trying to contact an agent on the sandbukta908b.ross.no server.  (The group name could not be found (0x800708AC))
    If I stop the VMM agent prior to starting the Add virtual machine host, the following error occurs:
    Error (410)Agent installation failed on sandbukta908b.ross.no.  (Fatal error during installation (0x80070643))
    Recommended ActionTry the operation again. If the problem persists, install the agent locally and then add the managed computer.
    Please advise,Morten

    DB:2.83:Add Virtual Machine Host: Error (2912) - The Group Name Could Not Be Found (0x800708ac)) p8

    Hello Carmen something I like to be clearer in the final decision on the issue have expressed the same mistake as the friend!
    I have to do uninstall admin console or admin server??installed the scvmm 2008 and the 2008 enterprise server with Hyper-V in the same machine,and when you try to add host on the same machine,you see this error...

  • RELEVANCY SCORE 2.83

    DB:2.83:Virtual Machine Connection Will Not Connect To Any Guest On One Host Via Hyper-V Manager kk


    No error message shows up, but in theHyper-V-VMMS log there's a 14090 - Virtual Machine Management service is shutting down while some virtual machines begin running. All running virtual machines will remain running with no management access. Any thoughts
    on how to resolve this?

    Thank you!

    DB:2.83:Virtual Machine Connection Will Not Connect To Any Guest On One Host Via Hyper-V Manager kk

    Hello SGilbert2012,
    Nice to hear that your issue solved.
    Sincerely,
    Murat DemirkiranIf the post helps you and remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. www.scvmm2012.com (TR Language) Please note that I'm not a Microsoft Representative
    or SpokesPerson.

  • RELEVANCY SCORE 2.83

    DB:2.83:Remote Console Can't Connect To Host j3



    Just installed VMware Server 2 Beta 3. When I launch the Remote Console, I get the following error:

    "Error opening the remote virtual machine butch:8333\48:

    A secure connection to the host could not be established."

    Host is Windows XP. Guest is Ubuntu 8.04 64-bit that worked today with VMware Server v1.

    Any ideas? Thanks.

  • RELEVANCY SCORE 2.83

    DB:2.83:Replication Error - Host Is Not Powered On Error. 8s



    I have a three host vcenter running esentials plus license ESXi 5.1.

    My issue is that, when I try to setup replication on one of the hosts vm machines I get this error message.

    " The virtual machine (machine name) has failed validation and cannot be configured for replication. Host is not powered on"

    The VM's are running.......

    VM's running on host 1 and 3 will allow replication setup and will replicate. But, on host 2, any of the VM's I try I get the error above.

    Thanks in advance,

    Ron

    DB:2.83:Replication Error - Host Is Not Powered On Error. 8s


    Well fixed it myself. Don't know what caused the replication appliance to say that the VM's were powered off on the 2nd host.

    Rebooting the affected host fixed the issue.

    " Have you tried turning it off and on again?" Duh.... Just didn't want to disrupt the users and systems on that host.

    Ron

  • RELEVANCY SCORE 2.82

    DB:2.82:Vcap - Consoles Not Able To Connect.. az


    Hi all.

    For those of you that that are using this tool, have a listen to this...

    All is working well, everything is populated (correctly), but when i go to use the console, I'm getting this error.

    "Error opening the remote virtual machine 192.168.**.** A4943\vm-436: The host name could not be resolved"

    Things to know: The 4943 part is the port number we are using, and i'm using the virtual appliance on esx3.5_U2.

    I can see that it's tryin to look at the ip:port \vm number, but it doesn't like the port number maybe Also, what's this "VM-436"? IS this a unique identifier for a virtual machine?

    What do you think?

    Cheers

    DB:2.82:Vcap - Consoles Not Able To Connect.. az

    Hi all.

    For those of you that that are using this tool, have a listen to this...

    All is working well, everything is populated (correctly), but when i go to use the console, I'm getting this error.

    "Error opening the remote virtual machine 192.168.**.** A4943\vm-436: The host name could not be resolved"

    Things to know: The 4943 part is the port number we are using, and i'm using the virtual appliance on esx3.5_U2.

    I can see that it's tryin to look at the ip:port \vm number, but it doesn't like the port number maybe Also, what's this "VM-436"? IS this a unique identifier for a virtual machine?

    What do you think?

    Cheers

  • RELEVANCY SCORE 2.82

    DB:2.82:Opening Microsoft Virtual Machine In Vmware Workstation 9 fa



    Hi,

    I am new to VMWare Workstation 9, and I am trying to open a Microsoft Virtual Machine (originally the XP Mode virtual machine) in VMWare. I used the File -- Open menu to open the virtual machine, and VMWare converted the Microsoft Virtual Machine. My host machine is running Windows 7.

    When I open the new virtual machine in VMWare Workstation, I am told I must register Windows. I don't have a serial number since this was a XP Mode virtual machine.

    How can I successfully convert an established Microsoft Virtual Machine into VMWare Workstation?

    Thanks,

    Mark

    DB:2.82:Opening Microsoft Virtual Machine In Vmware Workstation 9 fa


    Hi,

    I am new to VMWare Workstation 9, and I am trying to open a Microsoft Virtual Machine (originally the XP Mode virtual machine) in VMWare. I used the File -- Open menu to open the virtual machine, and VMWare converted the Microsoft Virtual Machine. My host machine is running Windows 7.

    When I open the new virtual machine in VMWare Workstation, I am told I must register Windows. I don't have a serial number since this was a XP Mode virtual machine.

    How can I successfully convert an established Microsoft Virtual Machine into VMWare Workstation?

    Thanks,

    Mark

  • RELEVANCY SCORE 2.82

    DB:2.82:Help Recovering Virtual Machine From Suspended State az


    I have a pretty big problem. I have a Windows XP Pro virtual machine that won't come out of suspended state. When I try to resume it it give this error message:

    unrecoverable error Unexpected signal: 11_[.|http://www.google.com/search?hl=ensa=Xoi=spellresnum=0ct=resultcd=1q=VMwareWorkstationunrecoverableerror%3A%28vmx%29%0AVmwareunrecoverableerrorUnexpectedsignal%3A+11.spell=1]_

    I've searched online and it seems to be related to memory somehow.

    All i really would like to do is somehow force the virtual machine to a shutdown state and restart it. I don't really care about loosing my suspended session in the guest.

    I'm running VMWare Workstation 6, on a CentOS linux host. I've also tried opening the virtual machine in VMWare Player with the same result.

    This is really bad because I had some really important files on that virtual hard drive. I'm open to any suggestions (even tools that could browse the virtual hard drisk to recover my files)

    DB:2.82:Help Recovering Virtual Machine From Suspended State az

    mikkanu wrote:
    I've tried deleting the .vmss file but that didn't fix it.

    Was the Virtual Machine window closed when you deleted the .vmss file?

  • RELEVANCY SCORE 2.82

    DB:2.82:Failed To Install Virtual Center Agent Service md



    When adding a host to virtual center, I receive the following status/error message, "Failed to Install the VirtualCenter Agent service. Then the host is grayed out in VirtualCenter with a red x and a disconnected note attached to the host name.

    Any ideas?

    DB:2.82:Failed To Install Virtual Center Agent Service md


    I got this error when I was connected to Virtual Center trying to add a host WHILE I also had a connection to the host in a separate Virtual Infrastructure window open at the same time.

    There must be some sort of glitch with Virtual Center 3.5 when trying to add a host when you have connected two sessions to it (one it Virtual Center adding the host, and one connected via virtual infrastructure direct to the host)...

  • RELEVANCY SCORE 2.82

    DB:2.82:Not A Valid Virtual Machine Configuration File 7d



    When opening up an virtual machine, the "not a valid virtual machine configuration file" error message pop up. I understand there is tool to generate the vmx file from the log file. Just wonder if someone can give me a hand to generate the file for me?

    Attached please find the log files in zip. VMware workstation version 8.

    Many thanks!

    Xiao

    DB:2.82:Not A Valid Virtual Machine Configuration File 7d


    The attached "WS8_Win7.vmx.zip" file contains a new "WS8_Win7.vmx" file created from the supplied vmware.log file.

    With VMware Workstation (or the target VM's tab) closed, unzip (double-click) the downloaded attached "WS8_Win7.vmx.zip" file and replace the original "WS8_Win7.vmx" file with the one here.

    Note that the virtual hard drive is configured as 'scsi0:0.fileName = "WS8_Win7-000002.vmdk"' and if that is not the Snapshot Disk you want to be running from then modify the option appropriately.

  • RELEVANCY SCORE 2.82

    DB:2.82:Vmware Workstation Latest Version f8



    When I power on the virtual machine, I get the following error message:

    "The network bridge on device VMnet0 is not running. The virtual machine will not be able to communicate with the host or with other machines on your network."

    Anyone know why this is happening?

    DB:2.82:Vmware Workstation Latest Version f8


    I was getting the VMnet0 error as well until I let VMware and the VMware Authorization Service access the internet. If I set those up in my firewall to be blocked, then I will get the VMnet0 error when starting the latest VMware version.

  • RELEVANCY SCORE 2.82

    DB:2.82:"Unexplained Error" Once Again z9



    Hello,

    I want to stress the "unexplained error" issue once again, which is the error message

    Error opening the remote virtual machine machinename:8333\number: An unexplained error occured.

    when connecting to the Remote Console. There was a suggested workaround:

    http://communities.vmware.com/docs/DOC-9390

    and everyone seemed to be happy.

    Well, I'm not, because that workaround fixed the problem only on the host where VMware Server was installed. For all remote connections (whether IE or FF) the error is still present.

    I'm using Vmware Server 2.0.1 on Windows Server 2008 SP2. NAT and DHCP service are disabled because I don't need them.

    Thanks,

    Sven

    DB:2.82:"Unexplained Error" Once Again z9


    I wouldn't want to do this for 2 main reasons:

    1. I don't want to install this huge package on every client just to access the console

    2. I can't imagine the performance will be the same

  • RELEVANCY SCORE 2.82

    DB:2.82:Error Code Listing 7x



    Would it be possible to obtain a pointer to a list of error codes for WS? At least let us know if this is proprietary and can't/won't be released. This might answer a lot of questions on this forum.

    Even Microsoft publishs theirs!

    Doing a google search I found one listing - but this seems to be for VIX only.

    TIA VMware.

    0 VIX_OKThe operation was successful.1 VIX_E_FAILUnknown error.2 VIX_E_OUT_OF_MEMORYMemory allocation failed: out of memory.3 VIX_E_INVALID_ARGOne of the parameters was invalid.4 VIX_E_FILE_NOT_FOUNDA file was not found.5 VIX_E_OBJECT_IS_BUSYThis function cannot be performed because the handle is executing another function.6 VIX_E_NOT_SUPPORTEDThe operation is not supported for the specified parameters.7 VIX_E_FILE_ERRORA file access error occurred on the host or guest operating system.8 VIX_E_DISK_FULLAn error occurred while writing a file; the disk is full. Data has not been saved. Free some space and try again.9 VIX_E_INCORRECT_FILE_TYPEAn error occurred while accessing a file: wrong file type.10 VIX_E_CANCELLEDThe operation was cancelled.11 VIX_E_FILE_READ_ONLYThe file is write-protected.12 VIX_E_FILE_ALREADY_EXISTSThe file already exists.13 VIX_E_FILE_ACCESS_ERRORYou do not have access rights to this file.14 VIX_E_REQUIRES_LARGE_FILESThe file system does not support sufficiently large files.15 VIX_E_FILE_ALREADY_LOCKEDThe file is already in use.16 VIX_E_VMDBThe system returned an error. Communication with the virtual machine may have been interrupted.20 VIX_E_NOT_SUPPORTED_ON_REMOTE_OBJECTThe command is not supported on remote objects.21 VIX_E_FILE_TOO_BIGThe file is too big for the filesystem.22 VIX_E_FILE_NAME_INVALIDThe file name is not valid.23 VIX_E_ALREADY_EXISTSAlready exists.24 VIX_E_BUFFER_TOOSMALLBuffer is too small.1000 VIX_E_INVALID_HANDLEThe handle is not a valid VIX object.1001 VIX_E_NOT_SUPPORTED_ON_HANDLE_TYPEThe operation is not supported on this type of handle.1002 VIX_E_TOO_MANY_HANDLESToo many handles are open.2000 VIX_E_NOT_FOUNDInvalid file - a required section of the file is missing.2001 VIX_E_TYPE_MISMATCHInvalid file - an object has the wrong type.2002 VIX_E_INVALID_XMLInvalid file - contents may be corrupt.3000 VIX_E_TIMEOUT_WAITING_FOR_TOOLSTimeout error while waiting for the guest tools to start.3001 VIX_E_UNRECOGNIZED_COMMANDThe command is not recognized by the virtual machine.3003 VIX_E_OP_NOT_SUPPORTED_ON_GUESTThe requested operation is not supported on this guest operating system.3004 VIX_E_PROGRAM_NOT_STARTEDA program could not run on the guest operating system.3005 VIX_E_CANNOT_START_READ_ONLY_VMCannot power on a read-only virtual machine.3006 VIX_E_VM_NOT_RUNNINGThe virtual machine needs to be powered on.3007 VIX_E_VM_IS_RUNNINGThe virtual machine should not be powered on. It appears to be running already.3008 VIX_E_CANNOT_CONNECT_TO_VMCannot connect to the virtual machine.3009 VIX_E_POWEROP_SCRIPTS_NOT_AVAILABLECannot execute scripts.3010 VIX_E_NO_GUEST_OS_INSTALLEDNo operating system installed in the virtual machine.3011 VIX_E_VM_INSUFFICIENT_HOST_MEMORYNot enough physical memory is available to power on this virtual machine.3012 VIX_E_SUSPEND_ERRORAn error occurred while suspending the virtual machine.3013 VIX_E_VM_NOT_ENOUGH_CPUSThis virtual machine is configured to run with 2 CPUs, but the host only has 1 CPU. The virtual machine cannot be powered on.3014 VIX_E_HOST_USER_PERMISSIONSInsufficient permissions in host operating system.3015 VIX_E_GUEST_USER_PERMISSIONSAuthentication failure or insufficient permissions in guest operating system.3016 VIX_E_TOOLS_NOT_RUNNINGGuest tools is not running.3017 VIX_E_GUEST_OPERATIONS_PROHIBITEDGuest operations are not allowed on this virtual machine.3018 VIX_E_ANON_GUEST_OPERATIONS_PROHIBITEDGuest operations are not allowed for the anonymous user on this virtual machine.3019 VIX_E_ROOT_GUEST_OPERATIONS_PROHIBITEDGuest operations are not allowed for administrative user on this virtual machine.3023 VIX_E_MISSING_ANON_GUEST_ACCOUNTThe virtual machine configuration must specify guest account name to be used for anonymous guest operations.3024 VIX_E_CANNOT_AUTHENTICATE_WITH_GUESTThe virtual machine cannot authenticate users with guest.3025 VIX_E_UNRECOGNIZED_COMMAND_IN_GUESTThe command is not recognized by the Guest OS tools.3026 VIX_E_CONSOLE_GUEST_OPERATIONS_PROHIBITEDGuest operations are not allowed for console user on this virtual machine.3027 VIX_E_MUST_BE_CONSOLE_USERThe command can only be run by console user.3028 VIX_E_VMX_MSG_DIALOG_AND_NO_UIThe virtual machine is blocked waiting for a user operation.3029 VIX_E_NOT_ALLOWED_DURING_VM_RECORDINGNot allowed while the virtual machine is recording.3030 VIX_E_NOT_ALLOWED_DURING_VM_REPLAYNot allowed while the virtual machine is replaying.3031 VIX_E_OPERATION_NOT_ALLOWED_FOR_LOGIN_TYPEThe command is not allowed by this login type.3032 VIX_E_LOGIN_TYPE_NOT_SUPPORTEDThis login type is not supported.3033 VIX_E_EMPTY_PASSWORD_NOT_ALLOWED_IN_GUESTThe guest does not support empty passwords.4000 VIX_E_VM_NOT_FOUNDThe virtual machine cannot be found.4001 VIX_E_NOT_SUPPORTED_FOR_VM_VERSIONThe operation is not supported for this virtual machine version.4002 VIX_E_CANNOT_READ_VM_CONFIGCannot read the virtual machine configuration file.4003 VIX_E_TEMPLATE_VMCannot perform this operation on a template virtual machine.4004 VIX_E_VM_ALREADY_LOADEDThe virtual machine has already been loaded.4006 VIX_E_VM_ALREADY_UP_TO_DATEThe virtual machine is already up-to-date.6000 VIX_E_UNRECOGNIZED_PROPERTYUnrecognized handle property identifier.6001 VIX_E_INVALID_PROPERTY_VALUEInvalid property value.6002 VIX_E_READ_ONLY_PROPERTYCannot change a read-only property.6003 VIX_E_MISSING_REQUIRED_PROPERTYThis handle is missing a required property.8000 VIX_E_BAD_VM_INDEXThe index parameter does not correspond to a result set.10000 VIX_E_INVALID_MESSAGE_HEADERA message header was corrupted or has the incorrect version.10001 VIX_E_INVALID_MESSAGE_BODYA message body was corrupted or is missing.13000 VIX_E_SNAPSHOT_INVALThe snapshot is incompatable with the current host.13001 VIX_E_SNAPSHOT_DUMPERUnable to open snapshot file.13002 VIX_E_SNAPSHOT_DISKLIBDisk problem.13003 VIX_E_SNAPSHOT_NOTFOUNDA file by that name does not exist.13004 VIX_E_SNAPSHOT_EXISTSA file by that name already exists.13005 VIX_E_SNAPSHOT_VERSIONSnapshots are not allowed on this virtual machine.13006 VIX_E_SNAPSHOT_NOPERMInsufficient permissions.13007 VIX_E_SNAPSHOT_CONFIGSomething is wrong with the configuration file.13008 VIX_E_SNAPSHOT_NOCHANGEThe state of the virtual machine has not changed since the last snapshot operation.13009 VIX_E_SNAPSHOT_CHECKPOINTUnable to save snapshot file.13010 VIX_E_SNAPSHOT_LOCKEDA snapshot operation is already in progress.13011 VIX_E_SNAPSHOT_INCONSISTENTThe snapshot files are in an inconsistent state.13012 VIX_E_SNAPSHOT_NAMETOOLONGThe filename is too long.13013 VIX_E_SNAPSHOT_VIXFILECannot snapshot all metadata files.13014 VIX_E_SNAPSHOT_DISKLOCKEDOne or more of the disks are busy.13015 VIX_E_SNAPSHOT_DUPLICATEDDISKThe virtual disk is used multiple times.13016 VIX_E_SNAPSHOT_INDEPENDENTDISKPowered on snapshot are not allowed on virtual machines with indpendent disks.13017 VIX_E_SNAPSHOT_NONUNIQUE_NAMEThe name does not uniquely identify one snapshot.14003 VIX_E_HOST_DISK_INVALID_VALUEThe specified device is not a valid physical disk device.14004 VIX_E_HOST_DISK_SECTORSIZEDisk sector size check failed.14005 VIX_E_HOST_FILE_ERROR_EOFRead beyond the end of file.14006 VIX_E_HOST_NETBLKDEV_HANDSHAKEError in protocol.14007 VIX_E_HOST_SOCKET_CREATION_ERRORUnable to create socket.14008 VIX_E_HOST_SERVER_NOT_FOUNDThe specified server could not be contacted.14009 VIX_E_HOST_NETWORK_CONN_REFUSEDThe server refused connection.14010 VIX_E_HOST_TCP_SOCKET_ERRORThere was an error in communication.14011 VIX_E_HOST_TCP_CONN_LOSTThe connection was lost.14012 VIX_E_HOST_NBD_HASHFILE_VOLUMENBD_ERR_HASHFILE_VOLUME.14013 VIX_E_HOST_NBD_HASHFILE_INITNBD_ERR_HASHFILE_INIT.16000 VIX_E_DISK_INVALOne of the parameters supplied is invalid.16001 VIX_E_DISK_NOINITThe disk library has not been initialized.16002 VIX_E_DISK_NOIOThe called function requires the virtual disk to be opened for I/O.16003 VIX_E_DISK_PARTIALCHAINThe called function cannot be performed on partial chains. Please open the parent virtual disk.16006 VIX_E_DISK_NEEDSREPAIRThe specified virtual disk needs repair.16007 VIX_E_DISK_OUTOFRANGEYou have requested access to an area of the virtual disk that is out of bounds.16008 VIX_E_DISK_CID_MISMATCHThe parent virtual disk has been modified since the child was created.16009 VIX_E_DISK_CANTSHRINKThe specified virtual disk cannot be shrunk because it is not the parent disk.16010 VIX_E_DISK_PARTMISMATCHThe partition table on the physical disk has changed since the disk was created. Remove the physical disk from the virtual machine, then add it again.16011 VIX_E_DISK_UNSUPPORTEDDISKVERSIONthan the version supported by this program.16012 VIX_E_DISK_OPENPARENTThe parent of this virtual disk could not be opened.16013 VIX_E_DISK_NOTSUPPORTEDThe specified feature isn't supported by this version.16014 VIX_E_DISK_NEEDKEYOne or more required keys were not provided.16015 VIX_E_DISK_NOKEYOVERRIDEWon't create unencrypted child of encrypted disk without explicit request.16016 VIX_E_DISK_NOTENCRYPTEDNot an encrypted disk.16017 VIX_E_DISK_NOKEYNo keys supplied for encrypting disk.16018 VIX_E_DISK_INVALIDPARTITIONTABLEThe partition table is invalid.16019 VIX_E_DISK_NOTNORMALOnly sparse extents with embedded descriptors may be encrypted.16020 VIX_E_DISK_NOTENCDESCNot an encrypted descriptor file.16022 VIX_E_DISK_NEEDVMFSFile system isn't VMFS.16024 VIX_E_DISK_RAWTOOBIGThe physical disk is too big. The maximum size allowed is 2TB.16027 VIX_E_DISK_TOOMANYOPENFILESThe host's limit for open files has been exceeded.16028 VIX_E_DISK_TOOMANYREDOToo many levels of redo logs.16029 VIX_E_DISK_RAWTOOSMALLThe physical disk is too small.16030 VIX_E_DISK_INVALIDCHAINInvalid disk chain: cannot mix hosted and managed style disks in the same chain.16052 VIX_E_DISK_KEY_NOTFOUNDThe specified key is not found in the disk data base.16053 VIX_E_DISK_SUBSYSTEM_INIT_FAILOne or more required subsystems failed to initialize.16054 VIX_E_DISK_INVALID_CONNECTIONInvalid connection handle.17000 VIX_E_CRYPTO_UNKNOWN_ALGORITHMSecurity library error.17001 VIX_E_CRYPTO_BAD_BUFFER_SIZESecurity library error.17002 VIX_E_CRYPTO_INVALID_OPERATIONSecurity library error.17003 VIX_E_CRYPTO_RANDOM_DEVICESecurity library error.17004 VIX_E_CRYPTO_NEED_PASSWORDSecurity library error.17005 VIX_E_CRYPTO_BAS_PASSWORDSecurity library error.17006 VIX_E_CRYPTO_NOT_IN_DICTIONARYSecurity library error.17007 VIX_E_CRYPTO_NO_CRYPTOSecurity library error.17008 VIX_E_CRYPTO_ERRORSecurity library error.17009 VIX_E_CRYPTO_BAD_FORMATSecurity library error.17010 VIX_E_CRYPTO_LOCKEDSecurity library error.17011 VIX_E_CRYPTO_EMPTYSecurity library error.17012 VIX_E_CRYPTO_KEYSAFE_LOCATORSecurity library error.18000 VIX_E_CANNOT_CONNECT_TO_HOSTCannot connect to host.18001 VIX_E_NOT_FOR_REMOTE_HOSTThis feature can only be supported on local host.20000 VIX_E_GUEST_VOLUMES_NOT_FROZENDrives are not frozen.20001 VIX_E_NOT_A_FILEThe object is not a file.20002 VIX_E_NOT_A_DIRECTORYThe object is not a directory.20003 VIX_E_NO_SUCH_PROCESSNo such process.20004 VIX_E_FILE_NAME_TOO_LONGFile name too long.

    DB:2.82:Error Code Listing 7x


    Would it be possible to obtain a pointer to a list of error codes for WS? At least let us know if this is proprietary and can't/won't be released. This might answer a lot of questions on this forum.

    Even Microsoft publishs theirs!

    Doing a google search I found one listing - but this seems to be for VIX only.

    TIA VMware.

    0 VIX_OKThe operation was successful.1 VIX_E_FAILUnknown error.2 VIX_E_OUT_OF_MEMORYMemory allocation failed: out of memory.3 VIX_E_INVALID_ARGOne of the parameters was invalid.4 VIX_E_FILE_NOT_FOUNDA file was not found.5 VIX_E_OBJECT_IS_BUSYThis function cannot be performed because the handle is executing another function.6 VIX_E_NOT_SUPPORTEDThe operation is not supported for the specified parameters.7 VIX_E_FILE_ERRORA file access error occurred on the host or guest operating system.8 VIX_E_DISK_FULLAn error occurred while writing a file; the disk is full. Data has not been saved. Free some space and try again.9 VIX_E_INCORRECT_FILE_TYPEAn error occurred while accessing a file: wrong file type.10 VIX_E_CANCELLEDThe operation was cancelled.11 VIX_E_FILE_READ_ONLYThe file is write-protected.12 VIX_E_FILE_ALREADY_EXISTSThe file already exists.13 VIX_E_FILE_ACCESS_ERRORYou do not have access rights to this file.14 VIX_E_REQUIRES_LARGE_FILESThe file system does not support sufficiently large files.15 VIX_E_FILE_ALREADY_LOCKEDThe file is already in use.16 VIX_E_VMDBThe system returned an error. Communication with the virtual machine may have been interrupted.20 VIX_E_NOT_SUPPORTED_ON_REMOTE_OBJECTThe command is not supported on remote objects.21 VIX_E_FILE_TOO_BIGThe file is too big for the filesystem.22 VIX_E_FILE_NAME_INVALIDThe file name is not valid.23 VIX_E_ALREADY_EXISTSAlready exists.24 VIX_E_BUFFER_TOOSMALLBuffer is too small.1000 VIX_E_INVALID_HANDLEThe handle is not a valid VIX object.1001 VIX_E_NOT_SUPPORTED_ON_HANDLE_TYPEThe operation is not supported on this type of handle.1002 VIX_E_TOO_MANY_HANDLESToo many handles are open.2000 VIX_E_NOT_FOUNDInvalid file - a required section of the file is missing.2001 VIX_E_TYPE_MISMATCHInvalid file - an object has the wrong type.2002 VIX_E_INVALID_XMLInvalid file - contents may be corrupt.3000 VIX_E_TIMEOUT_WAITING_FOR_TOOLSTimeout error while waiting for the guest tools to start.3001 VIX_E_UNRECOGNIZED_COMMANDThe command is not recognized by the virtual machine.3003 VIX_E_OP_NOT_SUPPORTED_ON_GUESTThe requested operation is not supported on this guest operating system.3004 VIX_E_PROGRAM_NOT_STARTEDA program could not run on the guest operating system.3005 VIX_E_CANNOT_START_READ_ONLY_VMCannot power on a read-only virtual machine.3006 VIX_E_VM_NOT_RUNNINGThe virtual machine needs to be powered on.3007 VIX_E_VM_IS_RUNNINGThe virtual machine should not be powered on. It appears to be running already.3008 VIX_E_CANNOT_CONNECT_TO_VMCannot connect to the virtual machine.3009 VIX_E_POWEROP_SCRIPTS_NOT_AVAILABLECannot execute scripts.3010 VIX_E_NO_GUEST_OS_INSTALLEDNo operating system installed in the virtual machine.3011 VIX_E_VM_INSUFFICIENT_HOST_MEMORYNot enough physical memory is available to power on this virtual machine.3012 VIX_E_SUSPEND_ERRORAn error occurred while suspending the virtual machine.3013 VIX_E_VM_NOT_ENOUGH_CPUSThis virtual machine is configured to run with 2 CPUs, but the host only has 1 CPU. The virtual machine cannot be powered on.3014 VIX_E_HOST_USER_PERMISSIONSInsufficient permissions in host operating system.3015 VIX_E_GUEST_USER_PERMISSIONSAuthentication failure or insufficient permissions in guest operating system.3016 VIX_E_TOOLS_NOT_RUNNINGGuest tools is not running.3017 VIX_E_GUEST_OPERATIONS_PROHIBITEDGuest operations are not allowed on this virtual machine.3018 VIX_E_ANON_GUEST_OPERATIONS_PROHIBITEDGuest operations are not allowed for the anonymous user on this virtual machine.3019 VIX_E_ROOT_GUEST_OPERATIONS_PROHIBITEDGuest operations are not allowed for administrative user on this virtual machine.3023 VIX_E_MISSING_ANON_GUEST_ACCOUNTThe virtual machine configuration must specify guest account name to be used for anonymous guest operations.3024 VIX_E_CANNOT_AUTHENTICATE_WITH_GUESTThe virtual machine cannot authenticate users with guest.3025 VIX_E_UNRECOGNIZED_COMMAND_IN_GUESTThe command is not recognized by the Guest OS tools.3026 VIX_E_CONSOLE_GUEST_OPERATIONS_PROHIBITEDGuest operations are not allowed for console user on this virtual machine.3027 VIX_E_MUST_BE_CONSOLE_USERThe command can only be run by console user.3028 VIX_E_VMX_MSG_DIALOG_AND_NO_UIThe virtual machine is blocked waiting for a user operation.3029 VIX_E_NOT_ALLOWED_DURING_VM_RECORDINGNot allowed while the virtual machine is recording.3030 VIX_E_NOT_ALLOWED_DURING_VM_REPLAYNot allowed while the virtual machine is replaying.3031 VIX_E_OPERATION_NOT_ALLOWED_FOR_LOGIN_TYPEThe command is not allowed by this login type.3032 VIX_E_LOGIN_TYPE_NOT_SUPPORTEDThis login type is not supported.3033 VIX_E_EMPTY_PASSWORD_NOT_ALLOWED_IN_GUESTThe guest does not support empty passwords.4000 VIX_E_VM_NOT_FOUNDThe virtual machine cannot be found.4001 VIX_E_NOT_SUPPORTED_FOR_VM_VERSIONThe operation is not supported for this virtual machine version.4002 VIX_E_CANNOT_READ_VM_CONFIGCannot read the virtual machine configuration file.4003 VIX_E_TEMPLATE_VMCannot perform this operation on a template virtual machine.4004 VIX_E_VM_ALREADY_LOADEDThe virtual machine has already been loaded.4006 VIX_E_VM_ALREADY_UP_TO_DATEThe virtual machine is already up-to-date.6000 VIX_E_UNRECOGNIZED_PROPERTYUnrecognized handle property identifier.6001 VIX_E_INVALID_PROPERTY_VALUEInvalid property value.6002 VIX_E_READ_ONLY_PROPERTYCannot change a read-only property.6003 VIX_E_MISSING_REQUIRED_PROPERTYThis handle is missing a required property.8000 VIX_E_BAD_VM_INDEXThe index parameter does not correspond to a result set.10000 VIX_E_INVALID_MESSAGE_HEADERA message header was corrupted or has the incorrect version.10001 VIX_E_INVALID_MESSAGE_BODYA message body was corrupted or is missing.13000 VIX_E_SNAPSHOT_INVALThe snapshot is incompatable with the current host.13001 VIX_E_SNAPSHOT_DUMPERUnable to open snapshot file.13002 VIX_E_SNAPSHOT_DISKLIBDisk problem.13003 VIX_E_SNAPSHOT_NOTFOUNDA file by that name does not exist.13004 VIX_E_SNAPSHOT_EXISTSA file by that name already exists.13005 VIX_E_SNAPSHOT_VERSIONSnapshots are not allowed on this virtual machine.13006 VIX_E_SNAPSHOT_NOPERMInsufficient permissions.13007 VIX_E_SNAPSHOT_CONFIGSomething is wrong with the configuration file.13008 VIX_E_SNAPSHOT_NOCHANGEThe state of the virtual machine has not changed since the last snapshot operation.13009 VIX_E_SNAPSHOT_CHECKPOINTUnable to save snapshot file.13010 VIX_E_SNAPSHOT_LOCKEDA snapshot operation is already in progress.13011 VIX_E_SNAPSHOT_INCONSISTENTThe snapshot files are in an inconsistent state.13012 VIX_E_SNAPSHOT_NAMETOOLONGThe filename is too long.13013 VIX_E_SNAPSHOT_VIXFILECannot snapshot all metadata files.13014 VIX_E_SNAPSHOT_DISKLOCKEDOne or more of the disks are busy.13015 VIX_E_SNAPSHOT_DUPLICATEDDISKThe virtual disk is used multiple times.13016 VIX_E_SNAPSHOT_INDEPENDENTDISKPowered on snapshot are not allowed on virtual machines with indpendent disks.13017 VIX_E_SNAPSHOT_NONUNIQUE_NAMEThe name does not uniquely identify one snapshot.14003 VIX_E_HOST_DISK_INVALID_VALUEThe specified device is not a valid physical disk device.14004 VIX_E_HOST_DISK_SECTORSIZEDisk sector size check failed.14005 VIX_E_HOST_FILE_ERROR_EOFRead beyond the end of file.14006 VIX_E_HOST_NETBLKDEV_HANDSHAKEError in protocol.14007 VIX_E_HOST_SOCKET_CREATION_ERRORUnable to create socket.14008 VIX_E_HOST_SERVER_NOT_FOUNDThe specified server could not be contacted.14009 VIX_E_HOST_NETWORK_CONN_REFUSEDThe server refused connection.14010 VIX_E_HOST_TCP_SOCKET_ERRORThere was an error in communication.14011 VIX_E_HOST_TCP_CONN_LOSTThe connection was lost.14012 VIX_E_HOST_NBD_HASHFILE_VOLUMENBD_ERR_HASHFILE_VOLUME.14013 VIX_E_HOST_NBD_HASHFILE_INITNBD_ERR_HASHFILE_INIT.16000 VIX_E_DISK_INVALOne of the parameters supplied is invalid.16001 VIX_E_DISK_NOINITThe disk library has not been initialized.16002 VIX_E_DISK_NOIOThe called function requires the virtual disk to be opened for I/O.16003 VIX_E_DISK_PARTIALCHAINThe called function cannot be performed on partial chains. Please open the parent virtual disk.16006 VIX_E_DISK_NEEDSREPAIRThe specified virtual disk needs repair.16007 VIX_E_DISK_OUTOFRANGEYou have requested access to an area of the virtual disk that is out of bounds.16008 VIX_E_DISK_CID_MISMATCHThe parent virtual disk has been modified since the child was created.16009 VIX_E_DISK_CANTSHRINKThe specified virtual disk cannot be shrunk because it is not the parent disk.16010 VIX_E_DISK_PARTMISMATCHThe partition table on the physical disk has changed since the disk was created. Remove the physical disk from the virtual machine, then add it again.16011 VIX_E_DISK_UNSUPPORTEDDISKVERSIONthan the version supported by this program.16012 VIX_E_DISK_OPENPARENTThe parent of this virtual disk could not be opened.16013 VIX_E_DISK_NOTSUPPORTEDThe specified feature isn't supported by this version.16014 VIX_E_DISK_NEEDKEYOne or more required keys were not provided.16015 VIX_E_DISK_NOKEYOVERRIDEWon't create unencrypted child of encrypted disk without explicit request.16016 VIX_E_DISK_NOTENCRYPTEDNot an encrypted disk.16017 VIX_E_DISK_NOKEYNo keys supplied for encrypting disk.16018 VIX_E_DISK_INVALIDPARTITIONTABLEThe partition table is invalid.16019 VIX_E_DISK_NOTNORMALOnly sparse extents with embedded descriptors may be encrypted.16020 VIX_E_DISK_NOTENCDESCNot an encrypted descriptor file.16022 VIX_E_DISK_NEEDVMFSFile system isn't VMFS.16024 VIX_E_DISK_RAWTOOBIGThe physical disk is too big. The maximum size allowed is 2TB.16027 VIX_E_DISK_TOOMANYOPENFILESThe host's limit for open files has been exceeded.16028 VIX_E_DISK_TOOMANYREDOToo many levels of redo logs.16029 VIX_E_DISK_RAWTOOSMALLThe physical disk is too small.16030 VIX_E_DISK_INVALIDCHAINInvalid disk chain: cannot mix hosted and managed style disks in the same chain.16052 VIX_E_DISK_KEY_NOTFOUNDThe specified key is not found in the disk data base.16053 VIX_E_DISK_SUBSYSTEM_INIT_FAILOne or more required subsystems failed to initialize.16054 VIX_E_DISK_INVALID_CONNECTIONInvalid connection handle.17000 VIX_E_CRYPTO_UNKNOWN_ALGORITHMSecurity library error.17001 VIX_E_CRYPTO_BAD_BUFFER_SIZESecurity library error.17002 VIX_E_CRYPTO_INVALID_OPERATIONSecurity library error.17003 VIX_E_CRYPTO_RANDOM_DEVICESecurity library error.17004 VIX_E_CRYPTO_NEED_PASSWORDSecurity library error.17005 VIX_E_CRYPTO_BAS_PASSWORDSecurity library error.17006 VIX_E_CRYPTO_NOT_IN_DICTIONARYSecurity library error.17007 VIX_E_CRYPTO_NO_CRYPTOSecurity library error.17008 VIX_E_CRYPTO_ERRORSecurity library error.17009 VIX_E_CRYPTO_BAD_FORMATSecurity library error.17010 VIX_E_CRYPTO_LOCKEDSecurity library error.17011 VIX_E_CRYPTO_EMPTYSecurity library error.17012 VIX_E_CRYPTO_KEYSAFE_LOCATORSecurity library error.18000 VIX_E_CANNOT_CONNECT_TO_HOSTCannot connect to host.18001 VIX_E_NOT_FOR_REMOTE_HOSTThis feature can only be supported on local host.20000 VIX_E_GUEST_VOLUMES_NOT_FROZENDrives are not frozen.20001 VIX_E_NOT_A_FILEThe object is not a file.20002 VIX_E_NOT_A_DIRECTORYThe object is not a directory.20003 VIX_E_NO_SUCH_PROCESSNo such process.20004 VIX_E_FILE_NAME_TOO_LONGFile name too long.

  • RELEVANCY SCORE 2.81

    DB:2.81:Error (23284) - He Virtual Machine Management Service Failed To Establish A Connection For A Virtual Machine Migration With Host : No Connection Could Be Made Because The Target Machine Actively Refused It. (0x8007274d). xk


    Hello everybody.
    I want migrate a virtual with VMM2012 SP1 from a standalone HyperV 2012 Host to a HyperV 2012 Cluster.
    The host and cluster are in the same AD domain.
    Live migration on host is enabled.
    Authentication protocol is Kerberos.
    Kerberos delegation is ok.
    VMM agent run on a domain admin account on all the host.
    When I start live migration thi error occured:
    Error (23284)
    Migration check for virtual machine xxxx failed to create a planned virtual machine in the target host. Detailed error message: The Virtual Machine Management Service failed to establish a connection for a Virtual Machine migration with host 'xxx': No connection
    could be made because the target machine actively refused it. (0x8007274D).
    Some ideas ?
    Thanks.
    Gabriel

    DB:2.81:Error (23284) - He Virtual Machine Management Service Failed To Establish A Connection For A Virtual Machine Migration With Host : No Connection Could Be Made Because The Target Machine Actively Refused It. (0x8007274d). xk

    Ciao,
    In attesa di ulteriori notizie, ho cambiatoil quesito in discussione generale.
    Facci sapereil feedback quando l'avrai,Anca Popa

    Microsoft offre questo servizio gratuitamente, per aiutare gli utenti e aumentare il database dei prodotti e delle tecnologie. Il contenuto viene fornito “così come è” e non comporta alcuna responsabilità da parte dell'azienda.

  • RELEVANCY SCORE 2.81

    DB:2.81:Error During Migration Of A Vm 9c


    I recieved this error when trying to migrate a VM to a remote server using Windows Server 8 on both Servers:
    PS C:\Users\Administrator Move-VM -Name OnTheMove -DestinationHost $RemoteServer
    Move-VM : Virtual machine migration operation for 'OnTheMove' failed at migration source 'SERVER-1950-01'. (Virtual
    machine ID 172C44E1-E34B-4896-B450-B41CB037638D)
    The Virtual Machine Management Service failed to establish a connection for a Virtual Machine migration with host
    'Server-1950-02': An existing connection was forcibly closed by the remote host. (0x80072746).
    Failed to send data for a Virtual Machine migration: An existing connection was forcibly closed by the remote host.
    (0x80072746).
    At line:1 char:1
    Move-VM -Name OnTheMove -DestinationHost $RemoteServer
    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
    CategoryInfo : NotSpecified: (Microsoft.Hyper...VMMigrationTask:VMMigrationTask) [Move-VM], Virtualizat
    ionOperationFailedException
    FullyQualifiedErrorId : OperationFailed,Microsoft.HyperV.PowerShell.Commands.MoveVMCommand

    Any ideas? Thanks.

    DB:2.81:Error During Migration Of A Vm 9c

    If the VM is on a share there is a bug preventing the VM from being moved.
    This might help http://www.youtube.com/watch?v=FXCHLjFCLsI

  • RELEVANCY SCORE 2.81

    DB:2.81:Oracle Drive Specific Features Not Working 9p


    I have set up Oracle Drive against two 10gR2 instances. Both of them fail with different messages.

    There are no issues with MS Web Folders, also most of this functionality works in Oracle Drive.

    When I try to use Drive specific functionality like "set properties", this fails with following messages.

    1. One of them fails with HTTP-404 after using machine name in the URL as opposed to using Virtual Host name
    2. Second one fails with similar error message but this is missing virtual host name or server name in the URL.

    I can't find any Oracle Drive logs to debug. So, my questions are ..

    1. how can I debug Oracle debug?
    2. Does Oracle drive support virtual host?
    3. If so, why is the above behaviour

    Users are keen to use Oracle Drive. So, any help (ASAP) would be appreciated.

    Regards,

    Bala Avula
    Kinetic Software Ltd

    DB:2.81:Oracle Drive Specific Features Not Working 9p

    We are very pleased to announce the Production Release 10.1.2.0 of Oracle Drive.

    You can download the software from here:
    http://www.oracle.com/technology/software/products/cs/index.html

    Note:
    - This version is production for English only. Other languages are Beta.
    - Oracle Drive 10.1.2.1 for ALL languages is expected soon.

    Find more information on Installation and Configuration as well as a Viewlet that shows Oracle Drive in Action here:
    http://www.oracle.com/technology/products/ias/portal/content_management_10gr2.html

    regards,
    Christian

  • RELEVANCY SCORE 2.81

    DB:2.81:Hello All, Need Your Assistance 8j



    Encountering the below error while Selecting the Resume Virtual Machine button

    The disk "D:\VM BI\Windows Server 2003 ENT\Windows Server 2003 ENT.vmdk" has internal consistency errors that may be caused by partial corruption of the disk file. It is recommended that you restore a backup of this virtual machine. If you do not have a backup, VMware Workstation can repair the disk, but there is a possibility that the data on the disk may be corrupt and affect the stability of the guest.

    Do you wish to repair the disk and continue?

    Either on clicking Yes or No

    Getting the below error message

    Cannot open the disk 'D:\VM BI\Windows Server 2003 ENT\Windows Server 2003 ENT.vmdk' or one of the snapshot disks it depends on.

    Reason: The specified virtual disk needs repair.

    Steps taken as per the article number
    Repairing a virtual disk in Workstation (2019259) is not working

    Windows Host
    To repair a virtual disk of a Workstation virtual machine in a Windows host, use the vmware-vdiskmanager utility that is installed by the Workstation installer in the installation folder on a Windows host.

    To use the virtual disk repair utility on a Windows host:
    Open a command prompt. For more information, see Opening a command or shell prompt (1003892). Change to the directory where Workstation is installed. By default, this directory is located at: Windows XP C:\Program Files\VMware\VMware Workstation Windows Vista/Windows 7 32bit C:\Program Files\VMware\VMware Workstation Windows Vista/Windows 7 64bit C:\Program Files (x86)\VMware\VMware Workstation Windows Server 2008 R2 C:\Program Files (x86)\VMware\VMware WorkstationRun the command:vmware-vdiskmanager -R path of the vmdk(virtual disk)Note: Where path of the vmdk(virtual disk) is the folder path to the virtual disk that appeared in the error.

    Specifications:

    Using Windows XP

    Workstation 6.0 VM

    VM Os Windows server 2003

    Please help, Thanks in advance

    DB:2.81:Hello All, Need Your Assistance 8j


    Hello continuum,

    Workstation 6.0 VM version of workstation is been used to run Windows 2003 server edition on local Windows XP OS

    Yes, you are right, It threw a syntax error for vmware-vdiskmanager -R path of the vmdk(virtual disk)

  • RELEVANCY SCORE 2.80

    DB:2.80:Problem When Migrate Ms Exchange To Virtual Machine 9a



    Hi,

    I have a SMTP node defined in my Solution Manager which send mails to external MS Exchange host without problems.

    There is a project for migrate Exchange to a virtual machine. When I modify the SCOT configuration for send mails to new virtual host, i get an error connection message.

    I check the exchange relay for my SAP machine and it looks right. There is no problems with net connections between sap system host and exchange host.

    Is necesary any special configuration or adaptation in SAP when migrate exchange server to a virtual machine???

    Thanks for all.

    DB:2.80:Problem When Migrate Ms Exchange To Virtual Machine 9a


    @Chetan,

    Sorry... but how are those links related to the problem?

  • RELEVANCY SCORE 2.80

    DB:2.80:Help:Error While Opening The Virtual Machine:Xxxxxx Is Not A Valid Virtual Machine Configuration File xf



    I've been using vmware player(Version 2.0.3) very happily for a long time now to run a winXP Pro,but I got the following message this day when I runing it.

    Error while opening the virtual machine:

    "S:\OFFICE2003\WXP\Win XP Pro.vmx" is not a valid virtual machine configuration file.

    Can somebody help please !!

    Thanks a lot!

    Best,

    Hahafx

    2009.12.07

    DB:2.80:Help:Error While Opening The Virtual Machine:Xxxxxx Is Not A Valid Virtual Machine Configuration File xf


    Hi Ulli,

    Ah .. didn't notice the alphabetic sorting, yes that makes sense.

    I noticed that there was no exotic character currently used in the vmx config file, but leaving the encoding out (Chinese Kuozhan) may end up resulting in problems when hahafx would want to, for example, start using shared folders with a character out of the standard US character set, which is why you can better leave it in.

    Internationalisation in software products is always a bit of a challenge

    --

    Wil

    _____________________________________________________

    VI-Toolkit amp; scripts wiki at http://www.vi-toolkit.com

  • RELEVANCY SCORE 2.80

    DB:2.80:Tf267042 And Tf266044 - Testing And Workflow Capabilities Failed fc


    I am new to lab management and just created my first environment. I installed lab agent, test agent, and build agent in the lab VM. However, testing and workflow capabilities are still listed as failed and repair capability does not help.
    I get the following error messages:
    Environment message: Type=Error; Message=TF267042: One or more machines are not ready to run tests. For more information, see the individual machine errors.;
    Machine messages:
    Machine name: Windows XP mit SP3 x86 Deutsch
    Machine message: Type=Error; Message=TF267049: Team Foundation Server encountered the following error while configuring the machine to run tests: TF260015: Exception occurred while checking registry of virtual machine Lab_766bb068-69f8-4c4e-9ee0-e7998ae2406a
    on host Holodeck.neovelop.de. Inner error is The RPC server is unavailable. (Exception from HRESULT: 0x800706BA).;
    --------------------------------------------------
    Environment message: Type=Error; Message=TF266044: One or more machines are not ready to run workflows. For more information, see the individual machine errors.;
    Machine messages:
    Machine name: Windows XP mit SP3 x86 Deutsch
    Machine message: Type=Error; Message=TF266015: The environment is not ready to run workflows because of the following error in Team Foundation Server: TF260015: Exception occurred while checking registry of virtual machine Lab_766bb068-69f8-4c4e-9ee0-e7998ae2406a
    on host Holodeck.neovelop.de. Inner error is The RPC server is unavailable. (Exception from HRESULT: 0x800706BA).;
    --------------------------------------------------
    How can I fix these errors?
    Thanks,
    MathiasMathias Raacke - freiberuflicher .NET Trainer und Berater - Blog http://www.outofcoffeeexception.de Twitter oocx

    DB:2.80:Tf267042 And Tf266044 - Testing And Workflow Capabilities Failed fc

    Thanks Mathias,
    I faced the same issue and as i didnt find the enable strict RPC compliance option on TMG, I did the below:
    IE - Tools -Internet Options -- Connectons tab -- click on LAN Settings button and check the proxy server -- click on Advanced and then give appropriate proxy server details and port details.
    it worked for me. workflow environmentand test capabilityare ready and build/test process started working fine.
    Note: i have made these changes in the test agent machine.
    thanks
    Ramesh Jammanapalli

  • RELEVANCY SCORE 2.80

    DB:2.80:Top Bar Not Displaying c3


    Hi all,
    Top bar getting error while opening the MS CRM 4.0When click on the Settings navigation bar also not displaying.
    Please help me out.
    Event vwr error.

    Event code: 3005
    Event message: An unhandled exception has occurred.
    Event time: 8/25/2010 11:09:34 AM
    Event time (UTC): 8/25/2010 5:39:34 AM
    Event ID: 699613dc85764c13a8a7aaa65e6cc5cb
    Event sequence: 492
    Event occurrence: 5
    Event detail code: 0

    Application information:
    Application domain: /LM/W3SVC/2/ROOT-1-129271879936257924
    Trust level: Full
    Application Virtual Path: /
    Application Path: C:\Program Files\Microsoft Dynamics CRM\CRMWeb\
    Machine name: Computername

    Process information:
    Process ID: 5724
    Process name: w3wp.exe
    Account name: NT AUTHORITY\NETWORK SERVICE

    Exception information:
    Exception type: MissingMethodException
    Exception message: Method not found: 'System.String Microsoft.Crm.Application.Utility.Util.GetSecureWebServerUrl()'.

    Request information:
    Request URL:
    http://ServerIp:5055/OrganizationUAT/_root/bar_top.aspx?area=SFAgroup=Extensionssubarea=lav_propertyproduct
    Request path: /OrganizationUAT/_root/bar_top.aspx
    User host address: 192.168.1.171
    User: Domain\userid
    Is authenticated: True
    Authentication Type: Negotiate
    Thread account name: NT AUTHORITY\NETWORK SERVICE

    Thread information:
    Thread ID: 1
    Thread account name: NT AUTHORITY\NETWORK SERVICE
    Is impersonating: False
    Stack trace: at Microsoft.Crm.Application.Menus.AppGlobalWebMenuBar.BuildMenuBar()
    at Microsoft.Crm.Application.Pages.Root.TopBar.ConfigureMenus()
    at Microsoft.Crm.Application.Controls.AppUIPage.OnPreRender(EventArgs e)
    at System.Web.UI.Control.PreRenderRecursiveInternal()
    at System.Web.UI.Page.ProcessRequestMain(Boolean includeStagesBeforeAsyncPoint, Boolean includeStagesAfterAsyncPoint)

    Custom event details:
    For more information, see Help and Support Center at
    http://go.microsoft.com/fwlink/events.asp.
    Thanks In Advaance
    Bhaskar.

    DB:2.80:Top Bar Not Displaying c3

    Hi,
    Resolved the issue, by doing below things
    1)Uninstall Microsoft.Crm.Application.Components.Core.dll from GAC
    2)Updated rollup 9
    Thanks Aand Regards,
    Bhaskar

  • RELEVANCY SCORE 2.80

    DB:2.80:Use A Windows Machine On A Linux Vmware Server fk



    Hi,

    I was using a windows server 2003 virtual machine with VMWare server on a windows host.

    By copying every files of the virtual machine (.vmx, .vmdk) i try to use the same virtual machine on a VMWare server on a Linux Host.

    Unfortunatly, when I try to run the VM on the linux Vmware server, an error message appears, saying that the .vmdk is not a virtual disk.

    can someone help me?

    thanks

    DB:2.80:Use A Windows Machine On A Linux Vmware Server fk


    OK, I've used an Ascii tranfer during the ftp session.

    No problem with the binary.

    Thanks everyone!

  • RELEVANCY SCORE 2.80

    DB:2.80:Message Host Not Responding - Bond 14 Days jc


    My environment consists of 4 Hosts with ESXServer 3.5 installed and1

    Virtual Center 2.5 (physical machine Windows Server 2003).

    HA and DRS enabled cluster set for the 4 Hosts. Number of host failures the cluster can tolerate 2.

    The virtual center reports that 3 of the 4 hosts not responding.

    4 Hosts and Virtual Center has connectivity. Respond by IP and by

    name (DNS). Both the 4 hosts, as the Virtual Center can be accessed via

    ssh and remote desktop.

    Questions

    The virtual center is an important feature that is not a point of

    failure in your virtual infrastructure. Even if he fails to guarantee

    the operation for a period of 14 days.

    The fact that 1 (for 3) Host not respond to the Virtual Center involves opening score of the 14 days?

    After 14 days, if restart occurs in 1 of 3 hosts that have multiple VM, what is the impact?

    How to restore the connectivity between the hosts and Virtual Center?

    It is enough, since the LAN is OK, the hosts command "service mgmt-vmware start" and restart the "network service"?

    Thanks

    / Bed

  • RELEVANCY SCORE 2.80

    DB:2.80:System Center App Controller Web Console c7


    Each time I tried to open a VM's console, I keep getting the error message Virtual Machine Manager failed to connect to the virtual machine because the host name (host name) could not be resolved by the Domain Name System.
    What port am I suppose to open on the firewall and to what machine am I suppose to open the port for in order to achieve this?

    I am trying to access the VMs from offsite. Onsite works fine because it's able to find the DNS for the server.

    DB:2.80:System Center App Controller Web Console c7

    Hi Arthur,
    Can you help me with remote app since we have not added the vms to any domain. When we try to connect to vm console via browser every time it asks for password and sometimes it fails to connect to VM
    Thanks

  • RELEVANCY SCORE 2.80

    DB:2.80:I Can Not Create Virtual Machine On Vista 32 Bit Host. 18



    Hi,

    My host is :Vista

    My Vmware is :

    VMware Virtual Infrastructure Web AccessVersion 2.0.0Build 84185

    VMware ServerVersion e.x.pBuild 84186

    When I try to create new virtual machine I click to "create virtual machine" and I write down virtual machine name and datastore (I use standard) Then click next. But nothing happens.

    I wait for an hour. No change.

    I couldnt get any error or event.

    I disable UAC in vista

    What is the problem? Or have you any trouble shoot method.

    Here are my machine screen captures:


    DB:2.80:I Can Not Create Virtual Machine On Vista 32 Bit Host. 18

    Hi there;

    I have kind of same error but the OS is W2K3 R2 SP2.

    When trying to create a virtual machine I an getting the following errors:

    1.- The client rejected a server response

    2.- TaskFailedExeption: Operation fail.

    I try it on W2K3 SP2 and works fine, probably is a known issue with the windows version.

    Any response will be appreciate

    Regards

  • RELEVANCY SCORE 2.80

    DB:2.80:Error Loading Virtual Machine: "Virtual Machine Config File Is Invalid." jp



    My host with GSX 3.0 server was showing a message error when I've tried to view my virtual machines in full screen mode. I've tried to solve the problem many times with Virtual Machine Console until the VMware crashed. After that, I've restarted the VMware service using the administrative tools in my Windows 2000 host server. The Windows virtual machines worked very well after that, but the Red Hat virtual machine didn't work anymore. Now, when a try do start the Red Hat virtual machine, the GSX 3.0 server displays the follow massage: "Virtual machine config file is invalid."

    What can I do to fix this problem ?

    Thanks,

    Alex.

    DB:2.80:Error Loading Virtual Machine: "Virtual Machine Config File Is Invalid." jp


    My problem was solved restarting my host server! Now, the linux virtual machine is working again.

    And the vmware.log is uptated when the virtual machine is working. If the virtual machine is not working, you must to take a look at vmware-serverd.log, that is the vmware server log.

    Thanks again,

    Alex.

  • RELEVANCY SCORE 2.80

    DB:2.80:Host Cpu Is Incompatable With The Versual Machine cx


    Dear I have created data center in with two ESXi servers, and I have created one 64 bit virtual machine inside the host name, but whenever I want to power on the machine it will show me below message

    DB:2.80:Host Cpu Is Incompatable With The Versual Machine cx

    Definitely look at VMware support. This forum is specifically for the product Microsoft Virtual Server 2005.

  • RELEVANCY SCORE 2.80

    DB:2.80:Vmware Remote Console sz


    Hi

    I have installed VMWare server 2.0 beta on windows 2003 R2 with SP2 which is a member machine and I have created one virtual machine for OS Windows 2008 64-bit.When I am trying to start and click on the console to open a remote console it gave me error

    Error opening the remove vritual machine isa01:8333/80 The host name could not be resolved

    Nagori

    DB:2.80:Vmware Remote Console sz

    Hi

    It is fixed now after I put the FQDN in the browser for URL

    Naorig

  • RELEVANCY SCORE 2.80

    DB:2.80:My Yahoo Messenger Is Blocked. I Get An Error Component_Type_Ycp Ycperror Ymsg.Coloselectionfailed .. Please Help xa


    Please help.

    I was told by my collegue about Microsoft security essentials. I liked it too.

    However, my yahoo messenger is being blocked. When I try to run the trouble shoot, the following message is given.

    Checking virtual IP servers...
    [VIP Raw] Connecting to Virtual IP server 127.0.0.1...
    [VIP Raw] Resolving host name 127.0.0.1... [PASSED]
    [VIP Raw] Connecting to Virtual IP server 127.0.0.1...
    [VIP Raw] Resolving host name 127.0.0.1... [PASSED]
    [VIP Raw] Connecting to Virtual IP server 127.0.0.1...
    [VIP Raw] Resolving host name 127.0.0.1... [PASSED]
    [VIP Raw] Connecting to Virtual IP server 127.0.0.1...
    [VIP Raw] Resolving host name 127.0.0.1... [PASSED]
    [VIP Raw] Connecting to Virtual IP server 127.0.0.1...
    [VIP Raw] Resolving host name 127.0.0.1... [PASSED]
    [VIP Raw] Connecting to Virtual IP server 127.0.0.1...
    [VIP Raw] Resolving host name 127.0.0.1... [PASSED]
    [VIP Raw] FAILED
    *** 'COMPONENT_TYPE_YCP' YCPError: 'YMSG.ColoSelectionFailed' ***

    Checking HTTP virtual IP servers...
    [VIP Http] Connecting to HTTP Virtual IP server 127.0.0.1...
    [VIP Http] Resolving host name 127.0.0.1... [PASSED]
    [VIP Http] Connecting to HTTP Virtual IP server 127.0.0.1...
    [VIP Http] Resolving host name 127.0.0.1... [PASSED]
    [VIP Http] Connecting to HTTP Virtual IP server 127.0.0.1...
    [VIP Http] Resolving host name 127.0.0.1... [PASSED]
    [VIP Http] Connecting to HTTP Virtual IP server 127.0.0.1...
    [VIP Http] Resolving host name 127.0.0.1... [PASSED]
    [VIP Http] FAILED
    *** 'COMPONENT_TYPE_YCP' YCPError: 'YMSG.ColoSelectionFailed' ***

    Please help.

  • RELEVANCY SCORE 2.79

    DB:2.79:Vmware Remote Console Doesnt Work ( Ubuntu 7.1 ) s3


    I think I have the same problem like many other people (had) with vmserver2 beta2.

    When I start a VM and try to see the console I get the error message:

    Error opening the remote virtual machine dev-vmware:8333\16:

    The host name could not be resolved

    Can someone please tell me, what I have to change (and where) to get this running?

    I saw in other threads, that this is a known issue, but I couldnt solve it on my own.

    DB:2.79:Vmware Remote Console Doesnt Work ( Ubuntu 7.1 ) s3

    OK - issue resolved

    When I opened the VMware Web Access page I used the URL http://mybox:8222 - which didn't work.

    With http://mybox.mydomain.com:82222 it worked (after disabling the porxy).

  • RELEVANCY SCORE 2.79

    DB:2.79:Vmware Remote Console Error mc



    Dear All,

    I have installed the latest vmware server 2.0.When try to connect to the virtual machine via VMWare Remote console I get the below message.

    Error opening the remote virtual machine localhost:8333\16:

    An unexplained error occured.

    As mentioned in some of the post I tried giving localhost,ip address instead of the actual machine but no luck even my host file configuration is right.

    Initially I thought there is a problem with my machine I tried the setup in a different machine but I get the same error.

    My operating system is windows 2003 r2 standard edition.

    Any help will be greatly appreciated.

    Regards

    Bala

    Message was edited by: BalaPrab

    DB:2.79:Vmware Remote Console Error mc


    Error opening the remote virtual machine localhost:8333\16:

    An unexplained error occured.

    Do you by any chance have an HTTP proxy configured? If so, try disabling it and see if that helps. The other thing that could cause this is certain firewall settings; do you have any 3rd party firewall package running on the machine?