• RELEVANCY SCORE 3.41

    DB:3.41:Router-On-A-Stick zk






    Hi,

    Can anyone help me how to configure a router-on-a-stick? It would be very appriciated if explain as detailed. Tnx

    DB:3.41:Router-On-A-Stick zk


    On the router do the following:

    interface fastethernet0

    interface fastethernet0.10

    encapsulation dot1q 10 - 10 identify VLAN10

    interface fastethernet0.20

    encapsulation dot1q 20 - 20 identify VLAN20

    I usually prefer dot1q encapsulation instead of ISL (if you want to use isl change dot1q to isl; but cisco 2950 only support dot1q I don't know what kind of device you have....). So you create subinterfaces with the proper encapsulation command. On the switch you should configure the uplink for trunk since you want transport more than one VLAN traffic over the uplink.

    The id of subinterface is not significant, so it can be fastehernet0.21 for VLAN 20, but I prefer to use the VLAN id as subinterface id, anyway you will be confused.

    Bye

    FCS

    Rate me if I helped.

  • RELEVANCY SCORE 3.20

    DB:3.20:Router On A Stick Troubles Help!!!! fa






    Hello Guys,

    I am have setup router on a stick. I am using dot1q encapsulation for both sub-interface on the router. The router I am using is a cisco 2620 which has a fastethernet interface. I setup 2 different vlans using the 192.168.2.0/24 and 192.168.3/24 network addresses. I setup one pc on each vlan and gave them a ip address from each subnet. I then assign a valid ip for to the sub-interfaces to be the default gateway for the pc's. I am able ping the gateway of the pc's vlan I am on and the other vlan however when I attempt to ping the pc from the pc in the different vlan the ping fails. I can ping both pc's from the router with no problem. The switch I am using it a 2960G cisco switch running en dot1q trunking as well. Am I missing something? I have used packet tracer to make this happen with no problems at all.

    DB:3.20:Router On A Stick Troubles Help!!!! fa


    Windows Firewall can do some odd things on a device.

  • RELEVANCY SCORE 3.20

    DB:3.20:Router On Stick With Two Switches m9






    I understand the concept of vlans with a router on stick with one router and one switch but it is possible to connect to switches together and do vlans through the router?

    DB:3.20:Router On Stick With Two Switches m9


    Worked like a charm.  Was able to create two dhcp scopes on the router and pass out address to both devices on each vlan. Thanks for your help.

  • RELEVANCY SCORE 3.17

    DB:3.17:Vtp Server Placement, Router-On-A-Stick Vs Switch 8s



    Is there a benefit to having a switch act as a VTP server, and not a "router-on-a-stick"? What are the drawbacks to having the router act as the VTP server?

    DB:3.17:Vtp Server Placement, Router-On-A-Stick Vs Switch 8s


    Hmmm ... Cisco let's you config 6500's as a router and ours also act as the VTP server. I would expect 3550/3750 (enhanced image) products can to the same. By extension I would presume this *should* work (but I've been around long enough to know it might not :)).

    In case you missed it, did you set the VTP domain/passwd on both the router and switch to be the same? The native Vlan (VTP passes over this) needs to be the same too.

  • RELEVANCY SCORE 3.11

    DB:3.11:Home Networking Troubles With 2 Routers. 9x



    I hope someone can help me. I'm at my wits end...

    We have a dsl connection with a 4 port router as our primary router. One computer is plugged into the primary router and gets internet just fine. Now I have a Lynksys BEFSR41 router branching off the primary router and 2 other computers are hooked up to it. All computers get internet just fine. BUT... only the 2 computers on the BEFSR41 can see each other and cannot see the computer hooked up to the primary router. And the same is true with the computer on the primary router... It cannot see the other 2 computers on my workgroup. I've looked at other posts about disabling DHCP stuff, but I still cannot get it to work. It actually causes more problems the more I tinker with it. This is basically due to the fact that I don't really understand networking very well.

    What would I have to do, in a step by step nature, to get all computers to see each other on my workgroup? I would be eternally grateful for any help.







    Solved!
    Go to Solution.

    DB:3.11:Home Networking Troubles With 2 Routers. 9x

    Your main router does NAT (Network Address Translation). You use private IP addresses inside your LAN. IP addresses 192.168.1.* are not routed in the internet. If you sent something with that IP address into the internet it will quickly be dropped. Instead the router does NAT and maps the private IP addresses to your one public IP address on the internet port.

    Due to NAT, your LAN is inaccessible from the internet unless either a computer initiates a session into the internet or you configure port forwarding, triggering, DMZ host or UPnP. This is simply because the router does not know what to do with an unsolicited IP packet arriving at the public IP address and thus simply drops it. It's not a firewall although it has some similar effects like a firewall. So you don't have to worry.

    The reason why I wrote that comment before was simply because I sometimes wonder why some people think they can use two routers and chain them and miraculously the main router knows that traffic from the internet should not get into your LAN while the second router (which would work exactly the same if it replaced the main router) would let everything from its "internet side" (i.e. the side which is connected to the internet port) enter the LAN side of the second router. Most people except the main router to protect their LAN but once they have a second router don't expect the same "protection" from the second router between the internet port and the LAN port.

    Anyway, don't worry. Your main router still does its job...

  • RELEVANCY SCORE 3.06

    DB:3.06:Befsr81 Port Forwarding pm


    2.40.2 Oct 23 2001 firmware. Need to enable ports 9401 and 9402
    in order to use IPTVanywhere a slingbox type device. Can anyone help?

    I am an EE but am fearful of upgrading firmware without guidance as the
    router works fine now.

    Some guidance was provided by manufacturer of IPTV. But Upnp is not
    available on router firmware and ports 9401 9402 don't stick in router.

    DB:3.06:Befsr81 Port Forwarding pm

    Open routers set up apge using http://192.168.1.1 .....Under applications gaming tab ..... use ports 9401 9402 for forwarding ....

  • RELEVANCY SCORE 3.01

    DB:3.01:Cisco 881 With A Rogers Usb 3g Stick dk



    Has anyone on here stuck a rogers 3G stick into the USB port on this router and configured it as an interface? If you have please let me know how and if it's impossible please let me know why.

    Thanks,

    Brent

    DB:3.01:Cisco 881 With A Rogers Usb 3g Stick dk


    Hi Brent,

    The 3G HWIC might be of interest to you, but you'd need at least a 1841 modular ISR for it to work.

    http://www.cisco.com/en/US/products/ps7272/index.html

    HTH

    Kevin

  • RELEVANCY SCORE 3.00

    DB:3.00:Router On A Stick With 2 Switches d8



    which topoplogy is the right one? 2 switches connected to a router or a switch connected to the router and the other switch connect to the switch?

    ---

    Posted by WebUser Charalampos Skeleton C#39;trattou from Cisco Support Community App

    DB:3.00:Router On A Stick With 2 Switches d8


    Disclaimer

    The  Author of this posting offers the information contained within this  posting without consideration and with the reader's understanding that  there's no implied or expressed suitability or fitness for any purpose.  Information provided is for informational purposes only and should not  be construed as rendering professional advice of any kind. Usage of this  posting's information is solely at reader's own risk.

    Liability Disclaimer

    In  no event shall Author be liable for any damages whatsoever (including,  without limitation, damages for loss of use, data or profit) arising out  of the use or inability to use the posting's information even if Author  has been advised of the possibility of such damage.

    Posting

    Not enough information to say which is "right".  Either could work, much depends on capabilities of switches and router, what you're trying to do, and perhaps physical topology issues.

    Everything else being equal, the router connected to both switches might allow for better performance.

  • RELEVANCY SCORE 2.97

    DB:2.97:Vlan Types And Router On A Stick xz



    Two quick questions here.

    1. Do User/Data VLANs prevent voice and management traffic from accessing the other VLANs, or does it not work or what? I've read a few conflicting things about it.

    2. Does putting a router on a stick to allow for cross VLAN communications defeat the purpose of a VLAN? I thought VLANs were meant to block traffic from getting to other VLANs. Router on a stick sounds like buying a firewall and not plugging it in.

    I'm still a baby at Cisco, so try to keep it in simple terms please.   

    -Randall

    DB:2.97:Vlan Types And Router On A Stick xz


    Hi Randall,

    VLANs are used to create multiple network over a single switched physical topology. Imagine you wanted to have separate networks for, say, two or three different units in your company: developers, graphics, marketing, for security and management purposes. You would either buy a separate switch (or switches) for each of these units and keep the networks physically separate, or you will use a single switched topology and instead, create the (now logically) separate networks using VLANs.

    So VLANs are about virtualizing switches, much in a similar way to using VirtualBox or VMWare to virtualize PCs. Instead of having multiple pieces of the same hardware, you are using the same hardware and use additional mechanisms to virtualize it and create multiple instances. VLANs are just that - virtual broadcast domains spanning over a switched topology, separate and isolated on Layer2 between each other.

    However, having VLANs does not mean you want to prevent them from ever communicating. You want to contain the broadcasts, have VLANs to use separate IP ranges, exert tighter control over the inter-VLAN traffic. There may be legal reasons, however, why the VLAN networks for developers, graphics and marketing may be allowed to communicate for some purpose (say, the shared printer is in the marketing VLAN and everybody wants to print on it). That is why it is completely legal to request for inter-VLAN communication. This is accomplished by using a router-on-stick or using multilayer switches that perform inter-VLAN routing inside their hardware directly. In other words, just as you would interconnect multiple physically distinct switched networks with a router, you are doing the same with router-on-stick.

    1. Do  User/Data VLANs prevent voice and management traffic from accessing the  other VLANs, or does it not work or what? I've read a few conflicting  things about it.

    Any VLAN will keep the data within it closed and will not leak it to any other VLAN, unless the traffic is routed to another VLAN. So unless the VLAN carries IP traffic that is purposefully addressed to recipients located in another VLAN (or another network), this traffic will not leave its original VLAN. In addition, it must be a router that takes packets from one VLAN and puts them into another, so the inter-VLAN communication is not provided by switches but only by routers or devices capable of routing.

    2. Does putting a router on a stick to allow for cross VLAN communications defeat the purpose of a VLAN?

    Not at all - think about the reasons described before.

    You are certainly welcome to ask further!

    Best regards,

    Peter

  • RELEVANCY SCORE 2.93

    DB:2.93:Enabling Upnp Troubles 3x


    I have the BEFSR41 Linksys router. I am trying to enable UPnP so My playstation 3 will change the NAT type from 3 to 2. NAT type 3 restricts me from using voice communication. I typed in 192.168.1.1 into my browser. My router came up with the settings. I checked the box that said "Enable UPnP." It told me to enter the password. (I never made a password for the router and assumed it was ADMIN like the default login) Well it wasnt. Now i cant even access my router page, and my ps3 still has NAT type 3. Can some one please give me some assistance. 1) Another way to configure my router to obtain NAT type 3 on ps3 2) A way to change my router password so I can maybe enable UPnP Im open to all other ideas and help, Thank you

    DB:2.93:Enabling Upnp Troubles 3x

    well in this case you need to reset the router back to factory default settings...logon to www.linksys.com/download and download the firmware for the router...try resetting the router back to default settings...logon to the router's setup page and try reflashing/upgrading the firmware on the router...after upgrading the firmware on the router reset it and reconfigure it according to ISP settings and try using UPnP or try triggering 6000 to 6999 and 10070 to 10080 ports on the router...check whether it makes any difference or not and let me know...

  • RELEVANCY SCORE 2.91

    DB:2.91:Cisco Vpn 3000 Concentrator - On-A-Stick 8p



    Need to know if the VPN 3000 concentrator can be setup with "on-a-stick" configuration.

    I know we can do this with a Cisco router using a Loopback interface. But I am not sure if the Cisco 3000 Concentrators can do the "on-a-stick" VPN.

    DB:2.91:Cisco Vpn 3000 Concentrator - On-A-Stick 8p


    Thank you for answering the question.

    After I posted the question, I have found out that it can be done. I'd some theory on it (exactly what you are saying) but had never implemented one.

    We tested our setup yesterday and it worked.

    For other members, just to let you know how this is done....

    Configure the IPSec tunnel (or other tunnels) just as if you were configuring them in a regular setup. Have only one route in the concentrator i.e. the default route, pointing out the interface you want active. Additionally, you may shut down the other interface(s) that are not being used. Then comes the trick of configuring the on-a-stick.

    Create rules that define the unencrypted traffic. You have to create rule-pairs, one of each direction. For example, if you want to have HTTP traffic that came over an encrypted tunnel go out the same interface (this is the on-a-stick part), then you have to create a rule for the outbound direction w.r.t. the unencrypted traffic and one for the inbound direction (which is the return/response traffic that went out). The direction is relative to the interface.

    NOTE:

    The traffic going out (after being unencrypted) will have destination port TCP/80. The traffic coming back from the web server will have SOURCE PORT TCP/80.

    So, for every type of traffic you want to send/receive, there will be a rule-pair - one outgoing + one incoming.

    Add these rules to the Public (Default) filter and you should be good to go. If the Public filter has been modified, then you may want to check the order of the rules just to make sure that there is nothing dropping the traffic before it hits its permit rule.

    It is imperative that you be as specific as possible in defining the traffic. Especially when dealing with packets that have non-RFC 1918 IP address as they can be routed over the Internet.

    If anyone wants further details on this subject, feel free to ping me at paras@indianware.com.

  • RELEVANCY SCORE 2.91

    DB:2.91:Router On A Stick Without Vlans? 9k



    I have a situation where 15 subnets are needed but my switch only supports 8 vlans. I thought that while I was preparing for my CCNA that we did a lab where we created a router on a stick using loopback interfaces without involving VLANs, or did I just imagine this lol. I keep deadending everytime i try this in packet tracer.

    Any thoughts?

    DB:2.91:Router On A Stick Without Vlans? 9k


    Jon

    Thank you for taking the time to clarify this issue for me.

    Clayton

  • RELEVANCY SCORE 2.91

    DB:2.91:Encapsulation Mode Router-On-A-Stick 7a



    I want to use router-on-a-stick method on cisco 2600 , after creating a sub-interface, can not use "encapsulation" command to define encapsulation method and it's vlan .

    How to correct this that can use "encapsulation" command ?

    The IOS version is 12.2(3) .

    DB:2.91:Encapsulation Mode Router-On-A-Stick 7a


    Hi,

    For further info, please check Cisco Feature Navigator:

    http://tools.cisco.com/ITDIT/CFN/jsp/index.jsp

    HTH

    Mohamed

  • RELEVANCY SCORE 2.90

    DB:2.90:Router On A Stick 1p



    This may be a dumb question, but can you do router on a stick with a 1720?

    I have enabled ip routing, version is 12.27 ip/ids/fw. Every time i try to assign encap to a sub interface it recognizes the encap command until it comes time to tell it what type?

    DB:2.90:Router On A Stick 1p


    Actually, 802.1q does not require 100Mb or more. Its not documented as a requirement.

    It is ISL that does require Fast Ethernet.

    What you find on the website documented is what TAC will support. Some hardware, and software combinations will support things that are not documented.

    When you know or find some thing like this its nice, but just remember you are on your own when you have probs. Also newer releases will probably have it removed so if you are thinking about upgrading for a new feature you might lose your hidden feature.

    2610 and 2611 with IP PLUS I believe supports 802.1q but don't remember which code release.The 7206 I/O controller that is only 10Mb also did but I don't remember what code.

    I think I recall the 1720 also had an IOS that had 802.1q, but can't remember which one.

    Daniel

  • RELEVANCY SCORE 2.90

    DB:2.90:To All That Are Having Problems Connecting To Go!Messenger Service!!!!!!!! dz



    It seems that quite a few people are having trouble connecting to the service or have never actually been on the actual service. I myself is having a few troubles with this situatuion. these are just a few things that could help you out with trying to connect to the GO!MESSENGER service.

    1. Try backing up your memory stick then fromattting it.

    2. Try setting the time and date on your psp to the exact settings.

    3. Iv'e read up on some forums about GO!messenger and apperently if you connect to Go!messenger using maybe a friends wireless. then reverting back to your own then Go!messenger should connect

    The more advanced stuff!!! lol

    3. It seems that the connection type PPPoE (the sharing connection type)lets the GO!messenger work (yaaaay)as I tried this and i connected but i didn't stay like this for long because i then noticed a few other problems....I couldn't connect to most of the websites and i coudln't connect to my MSN so i reverted back to my usual connection type PPPoA (the selfish non sharing connection type).....which works completely accept letting me go on GO!messenger =(

    4. try updating your firmware on your wireless router. luckly i found a new firmwarefor my belkin router that apparently fixes the problem i have with not being able to access most websites using PPPoE, so then i should be able to have access to GO!messenger and go on all websites and MSN.

    These are all the ideas i have for now. ill keep every1 posted for upcomin ideas on how to fix the problem.

    DB:2.90:To All That Are Having Problems Connecting To Go!Messenger Service!!!!!!!! dz


    I had also problems with login in at gomessenger. I notice that I could login at different WIFI routers eg in Hotels. I had a speedtouch 580 WIFI modem. Yesterday I changed to a Speedtouch 780 modem. And guess? I finally could login at home after almost 6 months I first install Gomessenger.

  • RELEVANCY SCORE 2.89

    DB:2.89:Pix-To-Ios Tunnel, Nat On Stick d8



    I have a router configured with Nat on Stick. I need to setup a vpn tunnel from the router to a pix.

    Is this possible? Since I am using nat on stick, and there is no public address on the rouer.

    If so, please point me to a sample config if possible.

    Best regards

    DB:2.89:Pix-To-Ios Tunnel, Nat On Stick d8


    providing the pix has a static public ip, and the router (has no public ip assigned on any interface) has internet access, ezvpn is feasible.

    the pix will act as the ezvpn server; whereas the router will act as the ezvpn client. the only catch is that only host behind the router will be able to establish the vpn. nonetheless, once the vpn is completed, host from both sites will have access to each other.

    have a look at the doc:

    http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/products_configuration_example09186a0080241a0d.shtml

  • RELEVANCY SCORE 2.88

    DB:2.88:Vlan Problem (Router On A Stick) 9z



    Please refer to the diagram and output at

    http://blog.erealmedia.com/?p=28

    The proplem is that I can ping all VLAN sub interfaces on the router from PC0, I can also ping other computer connected to same switch Sw-AC1 only, but not other computer (eg PC4 and PC5) Please help me solve the problem.

    I using Packet Tracer 4.1 Simulator from Cisco.

    DB:2.88:Vlan Problem (Router On A Stick) 9z


    Yes, you are right Arif,

    I have designed this VLAN for what you have said, I also had similar experience too.

    Here is few things which I learned:

    Finding anything about port and marc address like (what is MAC address or Port no) this port fa0/1 belong?

    Sw-AC1#show mac-address-table

    Mac Address Table

    -------------------------------------------

    Vlan Mac Address Type Ports

    ---- ----------- -------- -----

    1 00e0.b061.5401 DYNAMIC Fa0/4

    22 0060.5c05.de01 DYNAMIC Fa0/5

    33 0060.5c05.de01 DYNAMIC Fa0/5

    To know which device this switch connected to... use show cdp neighbors

    Sw-AC1#show cdp neighbors

    Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge

    S - Switch, H - Host, I - IGMP, r - Repeater, P - Phone

    Device ID Local Intrfce Holdtme Capability Platform Port ID

    R1 Fas 0/1 151 R PT1000 Fas 0/0

    Sw-AC2 Fas 0/4 151 S 2950 Fas 0/1

    R1 Fas 0/1 151 R PT1000 Fas 0/0.1

    R1 Fas 0/1 151 R PT1000 Fas 0/0.22

    R1 Fas 0/1 151 R PT1000 Fas 0/0.33

    To know about root bridge.. use spanning-tree

    Sw-AC1#show spanning-tree

    VLAN0001

    Spanning tree enabled protocol ieee

    Root ID Priority 32769

    Address 0001.C7D9.99B4

    Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec

    Bridge ID Priority 32769 (priority 32768 sys-id-ext 1)

    Address 00D0.FFCD.B224

    Aging Time 300

    Interface Role Sts Cost Prio.Nbr Type

    ---------------- ---- --- --------- -------- --------------------------------

    Fa0/1 Desg FWD 19 128.3 Shr

    Fa0/2 Desg FWD 19 128.3 Shr

    Fa0/3 Desg FWD 19 128.3 Shr

    Fa0/4 Root FWD 19 128.3 Shr

    Fa0/5 Altn BLK 19 128.3 Shr

    VLAN0022

    Spanning tree enabled protocol ieee

    Root ID Priority 32790

    Address 0001.C7D9.99B4

    Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec

    Bridge ID Priority 32790 (priority 32768 sys-id-ext 22)

    Address 00D0.FFCD.B224

    Aging Time 300

  • RELEVANCY SCORE 2.86

    DB:2.86:Router On The Stick xd



    Hi,

    I am trying to simulate the currrent Cat 6500 MSFC network by using router on the stick.

    Using two router 2621 and a 2950 switch, I need to configure the HSRP redundancy on each sub-interface so that I can see the failover behavior.

    Would that be possible to specify the HSRP on the sub-int?

    Thanks


    DB:2.86:Router On The Stick xd


    Hello,

    yes, this is possible. Your subinterfaces can be configured with HSRP in the same way as with physical interfaces.

    Check this document (scroll down to the section ´ISL Encapsulation Configuration Examples´ and then select ´HSRP over ISL Configuration Example´):

    Configuring Routing Between VLANs with ISL Encapsulation

    http://www.cisco.com/en/US/products/sw/iosswrel/ps1831/products_configuration_guide_chapter09186a00800ca6fd.html#xtocid16

    HTH,

    Georg

  • RELEVANCY SCORE 2.86

    DB:2.86:E1000 Ics Usb-Stick Bitte Hilfe!!!! Plz Help!!!!! 9d



    Hallo

    Ich habe Win7 über dem das Internet mit einem USB-Stick läuft.

    Ich möchte gerne mit (ICS) meine Internet Connection dem Router sharen...

    Wie mach ich das? Immer wenn ich ICS freigeben drücke komme ich nicht mehr in

    das Router-Setup! Habe nur die Möglichkeit vor der ICS Freigabe den Router

    zu Konfigurieren. Ich hatte mal einen alten Router dort konnte ich den Router

    zum Accespoint umwandeln. Wie mache ich das beim Linksys E1000

    Danke für die Hilfe

    English:

    Hello

    I'm running Windows 7 on the Internet with a USB stick.
    I would like to share with (ICS) Internet Connection to my router ...
    How do I do that? Whenever I press release I can not get to ICS
    the router setup! Have only the possibility of the release of the ICS router
    to configure. I once had an old router where the router I was able to
    Accespoint to convert. How do I do that the Linksys E1000

    Thanks for help

    DB:2.86:E1000 Ics Usb-Stick Bitte Hilfe!!!! Plz Help!!!!! 9d


    Big Thx now it works

    1.i set my Internet Connection to AutoIp

    2. set the Internet Connection Typ to Automatic/DHCP

    3. Dhcp Off

    4. Now the router come not back but after a pc restart and Rouder restart he come back..

    5. now i set the ICS On and it works

    Thx, Expert !!!!

  • RELEVANCY SCORE 2.84

    DB:2.84:Re: Amazon Fire Stick Wont Connect To Amazon sk



    I'm also having the same exact problem. I sign on to my WiFi and then get can't connect to Amazon.com. I called the help line and after trying different things the sent out a second fire stick. Same issue. Talked to the tech guys and still no luck. Anyone have a suggestion before I return it and give up?

    DB:2.84:Re: Amazon Fire Stick Wont Connect To Amazon sk


    How far away is your Firestick from your wifi source? What is your wifi source?

  • RELEVANCY SCORE 2.84

    DB:2.84:Live Paint Troubles!!!!!! Waiting For Godot! cs



    Am I the only one having troubles with Live Paint in Illustrator CC?

    Basically it doesn't work!

    I have posted a previous discussion on the forum

    http://forums.adobe.com/thread/1250011

    I wrote to ADOBE Support

    of course I never got an answer from Adobe

    and of course all the problems are still unsolved

    So for the present time I will have to stick to CS6!

    keep waiting!

    DB:2.84:Live Paint Troubles!!!!!! Waiting For Godot! cs


    Same issue here, I am amazed that there are not more posts on it.

    A really big pain for workflow, I am just hoping that there is not a wait until the next major release for a fix, somehow given the speed at which other bugs were fixed it is a possibility...

  • RELEVANCY SCORE 2.84

    DB:2.84:Having Some Troubles 73


    OK guys, could really use some help.

    I'm trying to put in a wireless connection between two desktops, one in the family room and the other in the room across from it. I have my router hooked up to the cable modem computer and a wireless adapter card on the other computer.

    I've run the wireless setup wizard on both computers, Windows XP on both. The network shows up on the adapter computer but won't connect and the router computer doesn't show the network. Any advice?

    Dan

    DB:2.84:Having Some Troubles 73

    Ah, Masta grashoppa, you pulled out smelling like a wose.



    But don't take my word for it, ask a Comcast Forum Expert, or goto http://www.dslreports.com/Signature courtesy of Bladerunner

  • RELEVANCY SCORE 2.83

    DB:2.83:Befsr41 V2 Router Help... 3k


    hello, i just got this router and i'm having troubles with it. Sometimes i lose my internet connection, which i then have to power cycle the router to get my internet back.. and i also get ping timeouts on irc.. i have the latest firmware : 1.46.02, Aug 03 2004 ... thank you

    DB:2.83:Befsr41 V2 Router Help... 3k

    on the setup page of the router...try and adjust the MTU between 1492 and 1200.

  • RELEVANCY SCORE 2.83

    DB:2.83:Router On A Stick Configuration 71



    If a network is subnetted, like for example 192.168.1.0/24 is subnetted to 192.168.1.0/25 192.168.1.128/25, can a router on a stick configuration be used?

    DB:2.83:Router On A Stick Configuration 71


    No problem, glad to have helped.

    Just be aware if you use secondary addressing then you must have all the clients in the same vlan on the switch(es) ie. you are no longer routing between vlans.

    Jon

  • RELEVANCY SCORE 2.83

    DB:2.83:Router On A Stick Problems f9



    I have troubles with a router on a stick.

    3640-IOS=12.2(3).Voice-vlan=11 (ccm+phones)

    native vlan=10 (pc's). If there is a call between a softphone and a outside phone(via E1), there is one-way speech! (softphone is not hearable) If I make a loopback, and then an h323 bind to the voice-vlan-interface, the IPphones cannot be called from outside. Now we put a second interface interface in the route and it's ok, but that is only a workaround. (ther are only 2 vlans..) I tried dot1q and ISL as trunk to the router, didn't matter.

    There are no access-lists configured.

    If I put the call on hold on the softphone, and then resume, it's ok!!!???

    We think it's a bug, but might miss something...

    Thanx, ;-)

    Sascha

    DB:2.83:Router On A Stick Problems f9


    That is what we did! (I wrote it in my message, but maybe not so clear..)

    That worked, but then we couldn't recieve a call on the IPPhones from outside (E1).

    (b.t.w. the IPPHones are in vlan11, the softphonepc is in vlan10.)

    Sascha

  • RELEVANCY SCORE 2.83

    DB:2.83:Help The Newbie!! f3


    Hello again.I am still having troubles. I was able to get a peer to peer going but the router setup is killin me.Here's my setup.Cable modem--wireless router--rocket 5M (I want this to be a router) ---5 x loco 5m(one on each building)--wireless router on each loco5M..I cant get the rocket to communicate with the router feeding it.Please help. I know this is probably a simple thing, but I'm not a network guy, they are just asking me to do this because I'm good with computers..Thanks

    DB:2.83:Help The Newbie!! f3

    You could actually set all the saetilite router LAN ranges the same so excepting the WAN address they would all be identical....And just to restate this the Static IPs should all be outside the DHCP range on the Head Router..... You generally should restrict DHCP ranges to a number that is somewhat related to the number of clients it will serve addresses for to be neat and tidy....Go for it! ;-)Bob

  • RELEVANCY SCORE 2.83

    DB:2.83:Help! Troubles With Me Wrt310n Router! jz


    Every time I connect to my WRT310N router it says that I have only local access. What does this mean? Possible solutions? I've already restarted my router three times, and I'm at a complete loss

    (btw, I'm running vista, and I am using a Linksys WMP300N wireless card)

    Sorry, I'm not very bright, and I think I have exhausted my already limited networking knowledge, thanks in advance.

    DB:2.83:Help! Troubles With Me Wrt310n Router! jz


    First try to check when you Hardwired your computer to the Router, are you able to go online or not? if you able to go online, then you need make some wireless changes on your Router, try this settings on your router.

    Open an Internet Explorer browser page on your wired computer(desktop).In the address bar type - 192.168.1.1 Leave username blank in password use admin in lower case...
    For Wireless Settings, please do the following : -
    Click on the Wireless tab
    -Here select manual configuratioon...Wireless Network mode should be mixed...
    -Provide a unique name in the Wireless Network Name (SSID) box in order to differentiate your network from your neighbours network...

    - Set the Radio Band to Wide-40MHz and change the Wide channel to 9 and Standard Channel to 11-2.462GHz...Wireless SSID broadcast should be Enabled and then click on save settings...
    Please make a note of Wireless Network Name (SSID) as this is the Network Identifier...
    For Wireless Security : -
    Click on the Sub tab under Wireless Wireless Security...
    Change the Wireless security mode to WPA, For Encryption, select AES...For Passphrase input your desired WPA Key. For example , MySecretKey , This will serve as your network key whenever you connect to your wireless network. Do NOT give this key to anyone.

    NOTE : Passphrase should be more that 8 characters...

    Click on Advanced Wireless Settings
    Change the Beacon Interval to 75 Change the Fragmentation...
    Threshold to 2304 Change the RTS Threshold to 2307 Click on "Save Settings"...
    Now see if you can locate your Wireless Network and attempt to connect...

    After this try connecting to your Wireless network.

  • RELEVANCY SCORE 2.80

    DB:2.80:Ios Help Needed 3350 Switch/ Router j3



    I have a 3550 switch and a 2821 router for voice. Connected to the switch will be the 2811 router as well as phones and Call Manager. Can you someone let me know the min. s/w level I need on the switch to start the lab. Can it just be a L2 IOS and use the voice router as a router on a stick if so what level IOS - many thanks

    DB:2.80:Ios Help Needed 3350 Switch/ Router j3


    The 3550 is a layer2/3 switch no matter what version you are running . If you run enterprise then you get advanced routing protocols and other features that the base IOS does not have. If you want to runn it as a layer 2 switch just turn off routing, "no ip routing" . That being said if the 3550 can be used to route in your network scenario a layer2/3 switch will always be faster than a router at moving packets .

  • RELEVANCY SCORE 2.80

    DB:2.80:Cisco Linksys Wireless Wrt120n Troubles x3



    Okay so i had to setup a router today, i used the Installation disc it came with, and the internet seems to work for everyone else wirelessly. but my computer can't seem to connect to the Cisco WRT120N Router i set-up. Even tried installing it on a different computer, and i encounter the same problem, not sure what to do. did searching on google and even a bit in these forums if i missed something that would help please link. But other wise i would like to get this issue solved. WRT120N WR120N

    DB:2.80:Cisco Linksys Wireless Wrt120n Troubles x3

    GenesisRhapsodos wrote:

    Okay so i had to setup a router today, i used the Installation disc it came with, and the internet seems to work for everyone else wirelessly. but my computer can't seem to connect to the Cisco WRT120N Router i set-up. Even tried installing it on a different computer, and i encounter the same problem, not sure what to do. did searching on google and even a bit in these forums if i missed something that would help please link. But other wise i would like to get this issue solved. WRT120N WR120N

    What's the firmware of this router? I suggest updating the firmware (if needed). You can download it here http://homesupport.cisco.com/en-us/support/routers​/WRT120N. Make sure to reset and reconfigure. That specific computer that you are having problem with, is that working with another wireless network (security enabled)?

  • RELEVANCY SCORE 2.79

    DB:2.79:Troubles With My Connection [Edited] aj



    I am currently signed up under a 3m service but acording to speedtest.net and my router via 192.168.1.1 im getting anywhere from 1.5 to 1.7 m could it be a routerbox limitaion(gt704wg) bad programming or a bad line any help would be nice. Also let it be note that i never recieved the 3m service and the only reason im concerned now is becaus im considering upgrading to 7.1m service and wouldlike this resolved first.

    Thanks Sam
    Message Edited by portdrake on 02-19-2009 06:19 PM

    DB:2.79:Troubles With My Connection [Edited] aj

    I am experiencing the same issue after upgrading from 768KBs to 3MBs. I ran the Verizon and Speedtest.net and am getting download speed of about 1500K and upload of about 370K. I ran all of the suggested items under the slow connection section except for the Optimizer because i am running Vista. Shouldn't I be getting closer to 2800KB download and 750KB upload? Yes I am thrilled with the speed being twice as fast as before, but it should be much faster. Any suggestions?Message Edited by HammerJ on 02-20-2009 07:15 PM

  • RELEVANCY SCORE 2.79

    DB:2.79:Urgent: Router On A Stick On A 1721 With Basic Ip Ios zj



    The title speaks for itself - can it be done? The router has 12.3 IOS and a fast ethernet card.

    I need just two vlans, with only few clients to support on both of them.

    Thanks a lot for any help!

    DB:2.79:Urgent: Router On A Stick On A 1721 With Basic Ip Ios zj


    Hi B,

    You will not be able to do router on stick with IP only feature in your IOS. The IOS should be having IP PLUS feature.

    Also to have that done you need to create subinterfaces and then under subinterfaces you have to configure encapsulation dot1q and then define an ip address. But encapsulation command only works with IOS having IP PLUS feature

    HTH

    Ankur

  • RELEVANCY SCORE 2.78

    DB:2.78:Jerky Dvd Play And Dma Dropping p9



    Hi!

    My dvd is performing poorly it is very jerky (ie drops alot of frames). I can use hdparm to turn dma on and it stick for a bit but hen it gets dropped. DMA being on seems to make a difference.

    I remember when i was testing the pos gentoo i had the same troubles and modprobing in ide-cd or something like that solved it though the option does not appear to be available here.

    any help is most welcome.

    DB:2.78:Jerky Dvd Play And Dma Dropping p9


    Solved! I tried a HDPARM setting suggest on the ogle site and that worked. The issue had to do with my VIA chipset. So if you have jerky play and DMA dropping with a VIA chipset use:

    hdparm -d 1 -X34 /dev/hdx

    and you should be happy as a clam

  • RELEVANCY SCORE 2.77

    DB:2.77:Mpls Vrf Forwarding Troubles After Ios Upgrade z7



    After an IOS upgrade from 12.2.18S to 12.2.25S7 on a 7206VXR-NPE300 I have MPLS VRF forwarding troubles. The problem is the router doesn't label the packets anymore. I did the following for debugging:

    LDP Discovery looks fine. MPLS Packet debugging show only incomming packets.

    With the command "sh ip bgp vpnv4 vrf CustA" all routes are present also with "sh ip route vrf CustA". But with "sh mpls forwarding-table vrf CustA 10.10.10.0 32" the route isn't visible.

    Is there a new command which I missed ?

    Thank your very much for your help.

    DB:2.77:Mpls Vrf Forwarding Troubles After Ios Upgrade z7


    So if I understand correctly, you can't even ping from CE to CE, right?

    Yes, that is correct.

    Could you please go on the egress PE and do a "show mpls fo

    Yes I see the label on the egress PE.

    Thank you for all your help. But I just solved my problem after an upgrade to 12.4(3) without changing the configuration.

    After the upgrade the command "sh ip cef vrf CustA" shows an Interface.

    10.10.10.0/24 212.101.3.18 GigabitEthernet2/0.550

    Maybe I missed a feature in 12.2(25)S7 :-(

    Regards

    Erich

  • RELEVANCY SCORE 2.76

    DB:2.76:2621xm Encapsulation Question ds



    while back I configure one of my cisco router on the stick, I remember getting the info over the net; and before I was a ble to  config the subint to an encapsulation I had to enable a command on the router, I did a mem erase on the unit, so now I need some help to get this router 2621XM enable it to run intervlans router ios c2600-i-mz.122-8.T10.bin, or it could be my other router ios c2600-ipbase-mz.123-6b.bin, I would really thankyou for your support...

    DB:2.76:2621xm Encapsulation Question ds


    Willy

    You don't actually close a question as such.

    If your question has been answered then you can use the ratings buttons to show that.

    Jon

  • RELEVANCY SCORE 2.76

    DB:2.76:Extra Objects On Copying Files 7f


    (A matter that caused troubles on going to a foto laboratory)Copying a folder to an Foto-Card or USB-Stick generates additional files with names like the originals plus a ._ in front of the name. and permissions -rwxrwxrwxIs this a feature? How to prevent?Any help would be great,KarlChanged: .- to ._ in second line

    DB:2.76:Extra Objects On Copying Files 7f

    Now the matter is quite clear to me, it was a theme at the MacOS time and at the transition to OSX, but forgotten in the meantime The only one task is to see and to operate (delete) the files before going to the shop, with your first post I am prepared better.I tried to search for dot files with terminal, though I am not trained well on it. Thank you, Karl

  • RELEVANCY SCORE 2.76

    DB:2.76:Router On A Stick With Dell 5324 sd



    Hi,

    i set up inter vlan routing with dell switch.I was able to ping hosts in vlan 10 from a host in vlan 30 but host in vlan 10 can not ping host in vlan 30

    Does somebody understand this ? Help.

    Here is the attached config.

    DB:2.76:Router On A Stick With Dell 5324 sd


    I would check the dell trunk setup sounds like something is not quite right. The native (untagged) vlan should be 1 by looking at your config , that would have to match on the dell. Also if you are using pc's as ping points make sure all software firewalls are shutoff otherwise they will not respond to ping.

  • RELEVANCY SCORE 2.75

    DB:2.75:Vlans On Rv082 Router 1a



    Hello, I'm having some troubles to configure vlan's on my RV082 Router. I have a Windows server with Active Directory, so I installed it on VLAN 1, but any other PC's out of VLAN 1 can't reach it, for example VLAN 2, 3 etc. So How must I to configure te VLAN's to get visibility from the server on all VLAN's? If I don't do this, all PC's can't login on Active Direcory Domain.

    I hope someone can help me

    Thanks

    Regards

    DB:2.75:Vlans On Rv082 Router 1a


    Hello, I'm having some troubles to configure vlan's on my RV082 Router. I have a Windows server with Active Directory, so I installed it on VLAN 1, but any other PC's out of VLAN 1 can't reach it, for example VLAN 2, 3 etc. So How must I to configure te VLAN's to get visibility from the server on all VLAN's? If I don't do this, all PC's can't login on Active Direcory Domain.

    I hope someone can help me

    Thanks

    Regards

  • RELEVANCY SCORE 2.75

    DB:2.75:Crowdsupport a9



    Hi,

    I just received a CG3100D-2BPAUS Modem and I am having troubles connecting the modem to my Netgear R6300 router.

    From the ethernet port on the modem, i connected an ethernet cable from there to my router's ethernet port. When i check the connection on the router, it doesn't connect to the internet. Please Help

    DB:2.75:Crowdsupport a9


    normally when i go to routerlogin.net it goes to my r6300 router settings. now it doesn't, it just times out

  • RELEVANCY SCORE 2.75

    DB:2.75:Router On Stick 1x



    can anybody tell me what does router on stick means how to config it with subneted network

    DB:2.75:Router On Stick 1x


    hi dhanraj,

    Router on stick means you are confiugring the intervlan routing using the router connected with your switch which are having multiple vlan...

    As we know different vlan can not communicate with each other directly...to make then communicate we need to have layer 3 functionality...so you can configre intervlan routing by the following way...

    if your switch is layer3 then you do not need to have router, then at that time you configuring the intervlan routing on the switch bye creating switch virtula interface SVI...

    but if your switch is not layer 3 and you want to make your vlan to be communicate with each other at that time you need to connect the router to switch and have to configure the router for the intervlan routing by creating multple sub interfacese on your router connected with the switch...and have to configure the trunking between the router and switch interface...

    for more help look at this link: http://www.cisco.com/warp/public/473/50.shtml

    hope this will help you

    rate this post if it helps: http://www.cisco.com/warp/public/473/50.shtml

    regards

    Devang

  • RELEVANCY SCORE 2.75

    DB:2.75:Disk Troubles ss



    oh woe is me....Im getting an error everytime i stick a blank cd-r in my drive.

    Unable to mount Blank CD-ROM Disc:

    mount: wrong fs type, bad option, bad superblock on /dev/sr1, missing codepage or other error In some cases useful info is found in syslog - try dmesg | tail or so

    DB:2.75:Disk Troubles ss


    try downloading cdrecord and see if you can burn.

  • RELEVANCY SCORE 2.75

    DB:2.75:Router Troubles zz


    Well ive recently connected my router which i havnt done in years. Its a Linksys WRT54G v.6.

    Before the Linksys would connect smoothly but now im having many problems with it. Whenever i connect it seems to turn off/on every minute.

    Whenever it dosnt reset for an amount of time it would show connection from the modem but who have no wifi or wired connection. After many times im able to connect....barely...i type in the default ip to access the routers home page but it says upload a fireware.I now have the download but cant access that page anymore.....any1 with any details to help plz post.

    DB:2.75:Router Troubles zz

    As you are getting "Management Mode Firmware Upgrade" page while accessing the router setup page,It seems that the firmeware is corrupted..Try this link and check if you were able to upgrade the router's firmware.

  • RELEVANCY SCORE 2.74

    DB:2.74:Intervlan Routing And Lan Wan Routing In A Single Router 11



    Hi

    Is it possible two configure Inter VLAN Routing ( Router on a Stick ) and LAN WAN Routing in a single Router.

    Pls Help

    Anish N

    DB:2.74:Intervlan Routing And Lan Wan Routing In A Single Router 11


    Hi

    I would like to suggest why dnot u use u r 3750 for intervlan routing.

    From where u r trying to get in to the router.?

    If from any port on the switch check the config of the switch and ur default-gateway should be sub-interface of the router.

    Thanks

    Mahmood

  • RELEVANCY SCORE 2.74

    DB:2.74:Nat Type Troubles zk



    hello,

    got a zyXEL G router with my new isp but its puting my ps3 under nat type 3.

    help,hazard




    DB:2.74:Nat Type Troubles zk

    you probably need to forward some ports i had to with my bt homehub when i had bt last year. check out portforward.com for instructions if you dont know how to do this.

  • RELEVANCY SCORE 2.74

    DB:2.74:Wvc200 Wireless Connection Troubles kd


    Linksys WVC200 camera connects fine using ethernet cable, but wireless doesn't appear to work most of the time. Router is Linksys WRT54G - (I have a laptop that connects fine wireless to this router). I am using fixed local network IPs, no security, channel 6. I want to eventually connect over internet from work, but as I cannot make camera function on my local home network, I have not tried outside yet. I have tried resetting camera setup, powering camera and router off, then powering up router until it settles, then powering up camera. Browser times out. Pinging camera IP times out 50% or more, rest return high response times. What am I doing wrong, or is my camera defective??? Because of my job situation, I cannot sit on hold with Linksys support to try to get answers... I would *really* appreciate your help!

    DB:2.74:Wvc200 Wireless Connection Troubles kd

    Hi,I've been having real problems getting the WVC200 to work at all, but I believe I've now found the problem, having got one of our techies at work to have a look at the whole setup. My issue is with the monitor software that comes with the camera, as soon as it is installed it screws up the PC totally and makes the camera unusable. Even when you uninstall it, the same thing happens. I eventually did a system restore and now it works fine with just the built in web app. So there is definitely something in the supplied software, my recommendation is don't use it! I will be contacting Linksys to try and get something that works!On the wireless side, if the aerial is upright, it freezes, with the aerial in the horizontal plane, it works fine, try that...PeteL...

  • RELEVANCY SCORE 2.74

    DB:2.74:Wmp54g Pci Adapter 9x



    Hi,

    I encountered some troubles with my Wifi connection at home.

    I have a Wireless Card on my computer (XP SP2) and a Linksys router WRT54GS.

    The connection is working fine most of the time, I have a secured with WPA encryption.

    When I try to download big files from a news server the connection is falling down andI'm not anymore able to connect to the Wireless router without restartingit by removing the power adapter.

    I think this is not normal, I have checked my modem and the connection is neverbeeninterrupted so I think this should be my WIFI adapterin my computer or my router whogetting some troubles.

    Could you please help me to found a solution about thisissue ?

    Thank you in advance foryour assistance.

    Regards.

    DB:2.74:Wmp54g Pci Adapter 9x


    Reduce the MTU size on router to 1350.

    Open internet explorer with 192.168.1.1

    Leave user name and password admin on the setup page you'll find MTU change it to Manual and change the size.

  • RELEVANCY SCORE 2.74

    DB:2.74:Befsr41 Troubles 89


    So I purchased the BEFSR41 Router, I followed all the instructions and hooked it all up when I try to go threw the install I get the following error message. "Router not found, please make sure the router is properly connected and try again" I also am not able to go to the web browser interface via http://192.168.1.1 nothing ever loads. I am attempting to set up the router threw my westell DSL modem and I am on Bellsouth Fastaccess DSL. Any help will be appreciated.

    DB:2.74:Befsr41 Troubles 89

    You cannot connect the Westell and the BEFSR41 together (and expect them to work)as long as they are both set to the192.168.1.x subnet.There are two solutions to your problem:******** Solution A******** As outlined by dibbler, you could fix your problem by doing the following:1) Power down your network2) Disconnect the Westell and the BEFSR413) Using an ethernet cable, connect your computer to one of the four LAN ports on the BEFSR41.4) Power up the BEFSR41 and your computer.5) Login to the BEFSR41 at 192.168.1.1 , and make the following change:Local IP address: 192.168.2.1(Note: Do not change the "Internet Connection Type". Leave it set at the factory default of "DHCP-automatic". )6) Click on the "Save Settings" button, and wait (3 to 60 seconds) for the screen to refresh. At this point in time, you will likely be disconnected from the router. Do not worry about this. Power down the computer and BEFSR41.7) Using an ethernet cable, connect the ethernet porton the Westell to the Internet port of the BEFSR41.8) Power up your network. It should work.Note: Your Westell is at 192.168.1.254Your BEFSR41 is at 192.168.2.1******** Solution B ********This solution is the preferred solution. In this solution, you set the Westell to "bridge" mode, thereby converting it to a plain ordinary modem. Here are the instructions:http://www.dslreports.com/faq/6323Note that the BEFSR41 in the instructions has a "WAN" port. This is the same as the "Internet" port on your router.Hope this helps.

    Message Edited by toomanydonuts on 09-04-2008 12:45 AM

  • RELEVANCY SCORE 2.74

    DB:2.74:Ncm Policies 9k



    I am having troubles getting NCM to read ACL lines on a router can anyone help?

    DB:2.74:Ncm Policies 9k


    I am having troubles getting NCM to read ACL lines on a router can anyone help?

  • RELEVANCY SCORE 2.74

    DB:2.74:2911 Router, Ping Ok But Web kd



    Hi i have some issues with router configuration. I cannot open any external web pages, but ping or telnet is just fine. Im using router-on-a-stick scenario. Router connected to LAN trough EtherSwitch module. Config attached.

    DB:2.74:2911 Router, Ping Ok But Web kd


    Thank you for rating helpful posts!

    regards,

    Leo

  • RELEVANCY SCORE 2.73

    DB:2.73:Site To Site Ipsec Vti + Vpn Client On A Stick d3



    Hi,

    Currently have a working site to site Ipsec VTI with zone-based firewall.

    Now I would like to configure the router to allow remote VPN client (using a stick) to access the network behind the router.(see attached diagram)

    Can the experts take a look at my configuration and advise me the problem.

    Thank you

    DB:2.73:Site To Site Ipsec Vti + Vpn Client On A Stick d3


    Hi,

    I amended as your advise but still have the same  error below: What may be the problem?

    Cisco Systems VPN Client Version 5.0.00.0340Copyright (C) 1998-2006 Cisco Systems, Inc. All Rights Reserved.Client Type(s): Windows, WinNTRunning on: 5.1.2600 Service Pack 3

    11     10:14:53.187  09/14/10  Sev=Warning/2    IKE/0xE300009BInvalid SPI size (PayloadNotify:116)

    12     10:14:53.187  09/14/10  Sev=Warning/3    IKE/0xA3000058Received malformed message or negotiation no longer active (message id: 0x00000000)

    Thank you

  • RELEVANCY SCORE 2.73

    DB:2.73:Serial Troubles In 3745 md



    Hi, I have a router 3745 with IOS c3745-ik9o3s-mz.123-5c in a flash of 128 Mb.

    The router has a module with 8 serial and when I configure any serial port and I plug the serial cable, suddenly the console doesn't work and of course the serial port either.

    Can anybody help me, please?

    DB:2.73:Serial Troubles In 3745 md


    Can you open a backdoor to the router by assigning an ip add. to ethernet, connect it to a hub or switch and then connect a PC in same segment (or use cross over cable). Configure the vty lines to accept telnet connections. See if you can telnet into the router when the router freezes..This would let us get inside the router and grab a show tech-support command output when the router freezes. Also you could allow access to the router through the AUX port and see if you can access the router when it freezes.

    You could also try the following alternatives,

    Try a different IOS version. IF you have a spare module, see if the same thing happens again. Are you trying to configure only one interface at a time (while the remaining serial interfaces are shutdown) or have you enabled all 8 serial interfaces at the same time. Try configuring one interface at at time, with the other interface shutdown.

    Hope that helps!

  • RELEVANCY SCORE 2.73

    DB:2.73:Router On A Stick j9



    Hi;

    can anyone point me in the direction of papers on the configuration of router on a stick? both the router side and the switch side. thanks in advance.

    DB:2.73:Router On A Stick j9


    Hi,

    Check this for Configuring NAT on stick router.

    http://www.cisco.com/en/US/tech/tk648/tk361/technologies_tech_note09186a0080094430.shtml#ex1

    Thanks

    Raj

  • RELEVANCY SCORE 2.73

    DB:2.73:Wd Live + Mybook Live + Wlan + Mkv km



    Configuration:

    MyBook Live with Cable on Router

    WD Live with USB WLAN Stick on WLAN

    when playing MKV files it starts to judder after 1 minute ((((

    Router supports N standard, and also my USB WLAN Stick supports N standard!

    MyBook Live is connected with 100Mbit cable!

    a little bit pissed about this juddering

    any ideas except connecting WD Live also with Cable because i dont want to do this!

    thanks for help

    pille

    DB:2.73:Wd Live + Mybook Live + Wlan + Mkv km


    pille444, maybe you should try contacting WD's Technical Support about this. You can do so either by phone or email.To Contact WD for Technical Supporthttp://support.wdc.com/contact/index.asp?lang=enRegards,




    Please click the star icon to the left to highlight helpful posts, and click on 'Accept as Solution' under post options for the post that solved your issue. This may help someone else.

  • RELEVANCY SCORE 2.73

    DB:2.73:Adv. Routing Troubles s1


    Im wondering if there is any way to map a port of the router to a local IPort address

    lets say computer X sends a messege to my router's non-local IP (65.78.100.100)
    Port:8080

    can i tell the router to resend that information to Local IP (192.168.1.100) port 8080

    as if the router was never there?

    because currently i cannot connect to my computer on a wireless network because its a private IP ,... so i need a way to connect to it from the outside world.

    if anyone has any ideas I sure could use the help.

    ~Vitus

    DB:2.73:Adv. Routing Troubles s1

    This is just a copy of the messege i sent neighbour_devil for any one who is interested in following this topic:

    I know i need to forward the port,... but i just cant seem to get it to work.
    the port the program is running on is port 8080
    its on 192.168.1.20

    the router(65.78.122.130) has a page called "port range forwarding" under the "applications and gaming" menu. I'm assuming it is the same thing because it looks very similair to pictures i've seen of the port forwarding screen

    i typed in theese values:
    start:8080
    end:8080
    protocol: both
    IP address:192.168.1.20
    enable : true
    I'm guessing that that forwards ports 8080~8080 to 192.168.1.20 using UPDTCP protocols, please correct me if i am mistaken.
    192.168.1.20 is a static IP.

    Hope you can help
    ~Vitus

  • RELEVANCY SCORE 2.72

    DB:2.72:Having Troubles Setting Up My Home Network pp


    I have a WRT54G boardband wireless g router. I have two computers connected to the internet through my router with no problems, been working great for months. I have Vista on both of my computers. I am trying to connect both of my computers through a network so I can shared files. I can't get this to work. I am not using the wireless router, I was told I could do it the way that I have it setup where both are connected through the router. If I need any additional hardware what would you recommend? I appreciate all the help.

    DB:2.72:Having Troubles Setting Up My Home Network pp

    I got very good link to file printer shoring .... try this....

  • RELEVANCY SCORE 2.72

    DB:2.72:311t + Wgr614v6 No Network Detect m1


    I've been using this router for several years and had no troubles from it. I recently updated it to the latest firmware off Netgear site.

    I'm using 4.1 drivers for the 311t card

    Fresh Clean install of xp service pack 3.

    Problem:

    Pc with 311t is approx 40 feet from router in wood frame home. No wireless telephones are in use, baby monitors, security systems etc...

    311t will locate network and show 45% signal strenght, will not connect with wep enabled on router. With router security turned off, router is not visible to 311t, however belkin router in another unknown residence is showing.

    Can anyone help me get connected and stable pls? I've resorted to using an ancient linksys 'b' usb stick on this machine and getting rock solid connections, just limited in speed. I'd like to see 'g' speeds. I bought this card in anticipation of getting an 'n' router.

    DB:2.72:311t + Wgr614v6 No Network Detect m1

    ok, to quote your page regarding my 'no ssid/no network found'

  • RELEVANCY SCORE 2.72

    DB:2.72:Offline Mode Second Device 7f


    On my primary device I have no troubles making albums and Individual songs available for offline play. ON MY SECONDARY DEVICE I cannot seem to get anything to stick for offline ( green arrow indicating its good to go) Any ideas/ similar problems?

    DB:2.72:Offline Mode Second Device 7f


    Try reinstalling the app.

    Also make sure you have enough storage





    Matt Suda Spotify Community Rock Star♫ Music keeps my heart beating ♫
    My Spotify DreamMeeting SpotifySpotify Profile@MattJSudaWebsite

  • RELEVANCY SCORE 2.72

    DB:2.72:Im Trying To Install A D-Link Router But It Wont Designate The Proper Ip Address. x9


    im trying to install a d link internet router and it wont get the proper ip address. i then tested it on my roommates laptop with a newer version of windows and the router worked. the d link tech said i may new new lan setting drivers installed to fix
    this problem. help anyone?
    original title:router troubles

    DB:2.72:Im Trying To Install A D-Link Router But It Wont Designate The Proper Ip Address. x9

    Check Dell support (here) for for driverupdates for your NIC (unless you didn't buy if from Dell).

  • RELEVANCY SCORE 2.71

    DB:2.71: Satellite C55 And Troubles With The Router 7c


    Hi can anyone help?

    I have just purchased a laptop Satellite C55 type and set it up yesterday and connected it to my broadband all going well , however switched the machine on today and everytine I connect to the internet it crashes the router and it restarts it I have to switch off the wifi before the router resets , I have other devices connecting just fine but the silly laptop just knocks it off?

    Please helpppppp??

    DB:2.71: Satellite C55 And Troubles With The Router 7c

    It doesnt matter which web page I try to load it just knocks the router off and have to turn the wifi off before it will reset itself .

  • RELEVANCY SCORE 2.71

    DB:2.71:Intervlan Routing And Nat pm



    hi i am trying to have the vlans communicate with each other using router on a stick , i have attached the packet tracer file for the same .

    i have configured subinterfaces on the router and still the vlans are not able to communicate with each other , please advise and help me .

    thanks .

    DB:2.71:Intervlan Routing And Nat pm


    Hello

    One is using the Fr cloud the other isn't

    no lmis or static mappings! 

    res

    paul

  • RELEVANCY SCORE 2.71

    DB:2.71:Troubles With The Program... ca



    Spotify has been finicky lately. When I open it, click on a song, the album artwork/title appears in the bottom left. When I click next, it will play the song, but the artwork/title will never change. If I can't find whatever I'm listening to in a long list, I have to click on the erroneous artwork to take me to whatever song I'm currently on.

    Also, in the radio portion it kinda does the same thing. It will stick on the first song's album artwork, while playing the next one...when I click next button, the artwork comes current, but restarts the song.

    Also (last one), when I connect to Spotify via Tumblr, it will often hiccup in the playback. Like it's frozen on a two second snippet.

    Do I reinstall the software...? Will I lose all my **bleep**...?

    Save me, Jebus.

    DB:2.71:Troubles With The Program... ca


    Spotify has been finicky lately. When I open it, click on a song, the album artwork/title appears in the bottom left. When I click next, it will play the song, but the artwork/title will never change. If I can't find whatever I'm listening to in a long list, I have to click on the erroneous artwork to take me to whatever song I'm currently on.

    Also, in the radio portion it kinda does the same thing. It will stick on the first song's album artwork, while playing the next one...when I click next button, the artwork comes current, but restarts the song.

    Also (last one), when I connect to Spotify via Tumblr, it will often hiccup in the playback. Like it's frozen on a two second snippet.

    Do I reinstall the software...? Will I lose all my **bleep**...?

    Save me, Jebus.

  • RELEVANCY SCORE 2.71

    DB:2.71:Ipsec Router On A Stick 9z



    Please tell me what are guidelines of configuring ipsec on a single interface. It would be nice to hear your success stories and see some working examples.

    Thanks!

    DB:2.71:Ipsec Router On A Stick 9z


    It is possible, personally I did it long ago, but i have seen it working fine, this all has to do with routing.

  • RELEVANCY SCORE 2.71

    DB:2.71:Router-On-A-Stick Intervlan 7k



    I have an old Cat 2900-XL which I believe is not capable of L3. Can I use a router with standard ethernet (10Mbps) for L3 functionality? I am under the impression that router-on-a-stick only works with full-duplex fast ethernet.

    Any information will be greatly appreciated. My goal is to perform InterVLAN on the switch. Thanks.

    DB:2.71:Router-On-A-Stick Intervlan 7k


    Thanks for all the input.

    Actually I also though I saw a post and a Cisco document that says trunking on a router only works on 100Mbps on an ISL. But you are right that this does not make a good solution for production network so I abandoned the whole idea. But it would be a great idea if you are stuck for an immediate solution so anymore inputs from guys out there will be appreciated. I do not have a lab to try it out so maybe somebody can try and post results.

    Thanks all.

  • RELEVANCY SCORE 2.71

    DB:2.71:Vlan On A Stick Using A 2621 8d



    Can I use a 2621and configure it as a router on stick. I have multiple vlans that I need to route between, but I don't know if the 2600 platform will support it. The attached switches are 2900.

    Thanx

    LB

    DB:2.71:Vlan On A Stick Using A 2621 8d


    Dave, it is a 2924. I've got the right code and I'm configuring now.

    Thanx

    LB

  • RELEVANCY SCORE 2.70

    DB:2.70:Issue With Wtr600n Router 3f


    I have attached a disc-on-key (memory stick) storage device to my router, but I cannot figure out how to access -- either from the wired computer or from any of the wirelessly connected computers.I would appreciate any help.

    DB:2.70:Issue With Wtr600n Router 3f

    Connect the HDD to the router ... access the setup page of router ... under storage tab .. check if you able to locate the HDD...Also you can use the search option under My Computer .... for search for computer or file ..... type in the Ip of the router ...it will show the router as a computer ....Open it it iwll HDD ... right click click MAP Drive ....After this you will able to access the Hard Drive ...

  • RELEVANCY SCORE 2.70

    DB:2.70:Voice Mail Troubles 1z



    When People call me or when I try to retrieve my voice mails all anyone hears in a busy signal, there are other phones on my plan and they have no troubles. Help!

    DB:2.70:Voice Mail Troubles 1z

    Call customer service - it sounds like you never set up your voicemail or it was never activated. A quick call to customer service should resolve this . . .

  • RELEVANCY SCORE 2.70

    DB:2.70:Troubles With Dhcp On Wrt350n dc


    Hi i am having a problem with my wrt350 N. The problem is that the router will work flawlessly for a couple of hours. Then suddenly i will get limited connectivity. I have a pc with a usb300n Usb adapter. And a laptop with a intel 4965 AGN. I also have 2 iphones that connect to the same router. The router gets internet from a adsl modem through dhcp. And i use wpa2 for security on all devices. The machines stay connected for say 6 hours then i need to power cycle the router to get it wo work again. I have tried to setup static dhcp but that did not resolve anything. Any help at all would be much apreciated.

    DB:2.70:Troubles With Dhcp On Wrt350n dc

    now i tried the settings gandalf suggested. And i will see if that has any effect on my problems. I have all my machines on the same workgroup. I can try to set all my machines to G mode. But that sort of defeats the purpose of going for Wireless N. I know it still is just a draft. But they could at least try and fix the problems with some better drivers.

    The problems where my machine has a full connection and still will not connect has reapeared now though. I wonder if it could have anything to do with me running utorrent on 2 systems simultaneously.

    Thanks a lot for all the help so far.

  • RELEVANCY SCORE 2.70

    DB:2.70:Using Asa For Intervlan Routing ak



    Hi!

    Can the ASA firewall be used to perform intervlan routing in the same way that a router would be used. (Router-on-a-stick).

    Thanks,

    Alvin

  • RELEVANCY SCORE 2.70

    DB:2.70:Connection Troubles With Vista X64 z8


    I just bought a WRT54GS and WMP54GS, however I'm having difficulties connecting to the wireless network. I'm not too sure if I set up the router correctly on the computer running XP, but I did follow all the instructions provided. When it comes to the wireless network adapter on Vista x64 however, I get nothing but troubles. I follow the instructions up to the point where it asks me to install the card and turn on the computer. I then wait for the installation wizard to pop up, but it never comes! Because of this, I doubt the installation of the adapter went correctly. Even though, when I try connecting to the router, it says connection unsuccessful, and does not let me connect to the internet. Any help would be greatly appreciated. Thanks!

    DB:2.70:Connection Troubles With Vista X64 z8

    I have the 64-bit version of Vista Home Premium, and it was a fresh install on my just-built computer.

  • RELEVANCY SCORE 2.69

    DB:2.69:Workstation Router Troubles m1


    I have a Linux based router (ClarkConnect Home 2.0) setup on my Ethernet LAN. I have a hub and Cat-5 cables to complete the physical network. (set up as modem-router-hub-workstations) I can surf from the router (text only). I can not get to the internet from the first workstation that I am setting up.

    I have a laptop that I am planning on addding to the network, but don't want to do so until I get the first station running.

    I have tried assigning an IP address to the workstation based on the information in the ClarkConnect manual (and the static IP settings for the gateway) and I have tried letting the router assign the workstation an IP. No luck either way. I have tried to ping the router from the workstation and vice versa, also no result (packets marked as lost)

    I am not using the uplink port on the hub and all of the appropriate lights on the back of the hub are lit, but no traffic though the workstation port.

    Any help would be great.

    What do I need to do to get my desktop workstation to get on line?

    DB:2.69:Workstation Router Troubles m1

    Never heard of ClarkConnect. If this a standalone device or a pc running a customer version of Linux?

    If you statically set the IP's on the workstations, can they ping each other? Can any of the other workstations ping the router? Any chance you have IP's assigned to the wrong ethx interface on the router?

  • RELEVANCY SCORE 2.69

    DB:2.69:Reflash Firmware 3s



    After playing around with my edgerouter i ran into some troubles that the router won't respond on the interfaces.

    Is there a complete image of teh usb stick inside that i can reflash on the router ?







    Solved!
    Go to Solution.

    DB:2.69:Reflash Firmware 3s


    It's not "officially" supported, but one of our community members compiled a rescue image that can be tftpbooted (assuming you have a console cable). Link to dmbaturin's rescue kit




    EdgeMAX Router Software Development

  • RELEVANCY SCORE 2.69

    DB:2.69:Socom Ftb, Router Problems. 98


    i am yet to find an answer to my troubles. i am trying to find out how to activate the voice thing on socom for the psp. i need to configure my router and i have no idea how. can anyone give me a rundown on how to configure my router?

    i looked at the router itslef and it says "canyon, 802.11g" on it. i presume it is a really crappy router but can anybody PLEASE tell me how to configure a router or more specifically this one. PLEASE PLEASE PLEASE!!!!!!!

    DB:2.69:Socom Ftb, Router Problems. 98

    can i ask a question as well, my coms dont work on FTB either, didnt mind as dont lay much but while there is a topic there...how do u put 2 ip addrresses into a DMZ?
    You cant... One only...



    Lee I PSN and Xbox Live: K1LLMEBILL I

  • RELEVANCY SCORE 2.68

    DB:2.68:Router-In-A-Stick Inter-Vlan Routing 31



    Hello,

    I'm using a Cisco 1720 with 12.2(2) IOS

    And the following command on the subinterface give an error:

    encapsulation dot1q 1

    Encapsulation command is available but with no parameters and it's not accepted alone.

    Is there any way to so that?

    Regards,

    Omar

    DB:2.68:Router-In-A-Stick Inter-Vlan Routing 31


    Hi,

    Can this be the cause -

    IEEE 802.1Q VLAN Routing - No on 1720 router -

    http://www.cisco.com/en/US/prod/collateral/routers/ps221/ps223/prod_end-of-life_notice09186a0080147795.html

  • RELEVANCY SCORE 2.68

    DB:2.68:Linksys Ea2700: Password Troubles s9



    Hello,

    several times I've tried to open router web-interface and just once I did it, other times I had a message "invalid router password..."

    I'm absolutely sure that the password has been entered is correct.

    The problem arises under local access mode.

    Please help me. What should I do for resolving this problem?

    DB:2.68:Linksys Ea2700: Password Troubles s9


    Hello again,St_Ujeen. Did you do the firmware update on a computer that was wired to the router? Please turn off the firewall on the PC when doing the update. Also do a hard first so that the settings are back to default.

    Redo the reset as described above once done.

    Try another PC if the issue pesists.

  • RELEVANCY SCORE 2.68

    DB:2.68:Isp Bandwidth Segregation 78



    Hi Experts,

    I have two vlans configured in my Switch 3560 and Router 3900.( Router on a stick configured for this).

    And i have 10Mbps ISP link to the router.

    Here i wnat to segregate my bandwidth as 5Mbps to each VLAN.

    Please help me to configure this on my router.

    With Regards,

    Janardhan

    DB:2.68:Isp Bandwidth Segregation 78


    Hi Experts,

    I have two vlans configured in my Switch 3560 and Router 3900.( Router on a stick configured for this).

    And i have 10Mbps ISP link to the router.

    Here i wnat to segregate my bandwidth as 5Mbps to each VLAN.

    Please help me to configure this on my router.

    With Regards,

    Janardhan

  • RELEVANCY SCORE 2.68

    DB:2.68:Router On A Stick With Cisco/Linksys Srw2024 Switch dd



    Does anybody have experience with configuring a router on a stick type configuration with a non-Catalyst switch? I have a SRW2024 switch and a 2611 router. I would like to configure the switch with a trunk port and use dot1q encapsulation on subinterfaces on the router to route between the subnets. Configuring the router is simple, but the switch is very confusing and I just can't seem to get it to work. Any ideas? Is this even doable with this combonation of hardware?

    Thanks in advance.

    -Dan

    DB:2.68:Router On A Stick With Cisco/Linksys Srw2024 Switch dd


    The "Encapsulation dot1q 1 native" command is not a valid command on my router. Specifically, the native command is not an option. Perhaps that isn't in my IOS version?

    IOS (tm) C2600 Software (C2600-JS56I-M), Version 12.0(7)T, RELEASE SOFTWARE (fc2)

    IOS image: c2600-js56i-mz.120-7.T

    However I did a whole lot of messing around with it today and I think I finally got it. The trouble is, IMHO, the switch menus are too messy and hard to understand. It seems to allow me to do impossible things which adds to the confusion.

    Here's what worked for me:

    My router config was correct to begin with.

    Router-A (Cisco 2611):

    interface Ethernet0/0

    ip address 192.168.1.10 255.255.255.0

    interface Ethernet0/0.2

    encapsulation dot1Q 2

    ip address 10.0.0.1 255.0.0.0

    Switch (Linksys SRW20204):

    Menu: Switch VLAN Interface Settings

    Select the port number of the port to be the trunk.

    Set Port VLAN Mode to Trunk. Submit.

    Menu: Switch VLAN

    Create a second VLAN with the ID of 2.

    Add the ports to be "Included" on this VLAN.

    Leave the workstation ports "Untagged".

    (This is where I was screwing up)...

    "Include" the Trunk port AND select "Tagged".

    So basically, I was tagging the workstation ports and not the trunk port. But the correct way is the Trunk port must be Included on all VLANs and have Tagging turned on for all VLANs. All the workstation ports should be included on whatever VLAN they should be on but NOT Tagged. It makes sense now because a workstation would have no idea what to do with a tagged frame.

    Why I can enable tagging on non-trunk ports is a mystery. They really should explain that better in the manual. Perhaps add some examples. I find the manual for this switch to be extremely vague overall.

    Thakns for the help guys!

    -Dan

  • RELEVANCY SCORE 2.68

    DB:2.68:Qos And Routing On A Stick xa



    guys just a quick question: i have configured router on a stick with various vlans routing on a single router fast ethernet port. if i apply a QOS service policy to the actual physical interface instead of the logical interfaces, will everything still work the same as applying the Service-policies to the individual logical interface of the vlan eg fa0/0.50

    Thanks

    DB:2.68:Qos And Routing On A Stick xa


    well it depends on what you configure on your service policy.

    If, for instance, you apply on it a cumulatice policer after a certain threshold is passed, you will be potentially affecting all the flows, even the ones which consume limited bandwidth.

    If on the contrary you classify based on vlan tags (if your platform allows that) or base on flows, in principle a phisical level policy can have the same effect of multiplan vlan policies. But again it all depends on what you actually configure.

    regards,

    Riccardo

  • RELEVANCY SCORE 2.68

    DB:2.68:Access List Troubles af



    I have a 1721 router, and a 506E firewall with NAT.

    Inside the network, we have a machine in which we wish to telnet into from the outside world. I have the router setup with static NAT so that machine has a public IP.

    I can ping that public IP successfully.

    When I TELNET to it, it always times out. I am guessing I need to open up the firewall on port 23. I am good with routers, but I am new with PIX firewalls. I tried this command:

    access-list TEL_IN permit any any eq TELNET

    I applied that to both interfaces. This did not work; actually it prevented my local PCs from getting on the network.

    Can you give me some ideas??

    FYI, I am on the job now so any help would be GREATLY appreciated!

    DB:2.68:Access List Troubles af


    just wondering what sort of pat/nat is configured on the pix; as with pix 506e, i.e. v6.x, nat/global or static is a must do.

    i guess static nat needs to be configured again on the pix.

    e.g.

    static (inside,outside) netmask 255.255.255.255

    access-list inbound permit tcp any host eq 23

    access-group inbound in interface outside

    clear xlate

    it would be better to modify the existing acl tel_in to the one above, as it presents a security risk by permitting any any.

  • RELEVANCY SCORE 2.67

    DB:2.67:Wrt160n V.2 / Xbox360 Troubles 73



    I am having zero luck getting my Xbox360's NAT to change off of Strict NAT.

    I have tried any and all methods i could find, some of which were probibly stupid.

    Im using a WRT160N V2 router with no modem.

    Everything on here is for v1's and v3's, and i doubt im the only one with this problem.

    HELP! (please)







    Solved!
    Go to Solution.

    DB:2.67:Wrt160n V.2 / Xbox360 Troubles 73


    I am having zero luck getting my Xbox360's NAT to change off of Strict NAT.

    I have tried any and all methods i could find, some of which were probibly stupid.

    Im using a WRT160N V2 router with no modem.

    Everything on here is for v1's and v3's, and i doubt im the only one with this problem.

    HELP! (please)







    Solved!
    Go to Solution.

  • RELEVANCY SCORE 2.67

    DB:2.67:2950 Vlan ks



    Hi Guys!

    Why does the other VLAN on my catalyst 2950 switch turns to administratively down when i try to up the other vlan. Example: i issue the command no shut on vlan 1 then my vlan 2 will turn to administratively down. same as vlan 3. i configured all the vlans to have different subnets. can someone please help me.

    Im trying to use Router on a stick config. Do i need to put ip address on each vlan or i will just create vlan then configure a trunk port for my router on a stick?

    tnx in advance....

    DB:2.67:2950 Vlan ks


    i agree with glen.grant and u can have only layer 2 vlans on cisco 2950 switch, dont assign ip addrees to other vlan apart from mangement vlan.

  • RELEVANCY SCORE 2.67

    DB:2.67:Iphone + Wi-Fi Troubles p7


    I am unable to connect to my wireless network on my iphone. it does not even pick up the signal. the wireless router is acting as a switch, and it is a netgear b and g. all other laptops and whatever get full signal, but the iphone doesnt see it. I have tried power cycling, resetting network, resetting the full phone. . . everything. . . Please help.

    DB:2.67:Iphone + Wi-Fi Troubles p7

    Yeah, the network is pretty complex. . . though I have made sure that the SSID was being broadcasted. The router is acting as a switch, using a sonicwall as a router/DHCP server. I went wardriving for a bit to search for other networks to connect too, and the iphone did not find any one of them. So I am assuming it is the phone, and I am going to call tomarrow, as well as go in. There is an apple store in my college town of Chico, which is ironically where I have to move back to tomarrow. We will see if I can't get this whole thing sorted out. Thanks a bunch for the input, from everyone.

  • RELEVANCY SCORE 2.67

    DB:2.67:Connect Usb Drive To D1000 Router mp



    Hi

    I am trying to connect a USB hard drive or memory stick to my D1000 Router. But

    i cannot see it via my laptop. And it does not appear on the "Virtual Device" on the router configuration when i log in.

    I have enabled file sharing to Public but still no joy.

    Any Help available please.

    Anthony

    DB:2.67:Connect Usb Drive To D1000 Router mp

    Hi chilly000

    We will not be able to recommend or advise on connecting a USB to the router as this is a functionality not agreed or supported by eircom, Although that is not to say other people can't help you.

    Thanks

    Al




    _________________________________________________________________________Common questions answered here!Click here to PM me

  • RELEVANCY SCORE 2.67

    DB:2.67:Wireless Internet Connection Troubles c8


    Hello. Got my MacBook Pro last week and can't connect to the internet since then. At home I've got a wireless connection: a cisco system router (series 800 A) is connected to a 3Com access point (3Com office connect wireless 54 Mbps 11 g). AirPort does see the 3Com connection: I click on it (doesn't ask for any password), but it doesn't connect to it. Thanks for any help!

    DB:2.67:Wireless Internet Connection Troubles c8

    Powerserg,
    Please start a new topic thread here, unless you are sligo_mm.
    What may work for Sligo_mm may not work for you, or vice versa. It is best to isolate issues in their own thread to ensure people don't try the wrong solution on their machines. To start a new topic thread, please post here:
    http://discussions.apple.com/forum.jspa?forumID=1297start=0

  • RELEVANCY SCORE 2.67

    DB:2.67:Router-On-A-Stick On Between 2610 And 2924 8s



    Is there a minimum IOS requirement for configuring router-on-a-stick for a router or switch? I've configured it before on other gear, but for some reason I've been having trouble setting it up for this switch. I have two vlans (native with no IP, 2nd VLAN with an IP), but I can't seem to do a "no shutdown" on my second VLAN's interface (no error returned, just sticks as no shutdown). Trunks are set up with dot1q. In the end, I can't seem to ping the router's subinterfaces. Any ideas?

    -Shikamaru

    DB:2.67:Router-On-A-Stick On Between 2610 And 2924 8s


    Thanks for replying, Davang. I worked it out. A couple of the configuration commands are a little different than I've seen before, but it's fine now.

    -Shikamaru

  • RELEVANCY SCORE 2.66

    DB:2.66:Cisco 871 As A Router On A Stick 3j



    Hi guys,

    I'm looking for a basic Cisco router I can use in a "router on a stick" scenario to route traffic for our video conferencing system either across our IPSec VPN network or through our Checkpoint firewall to the web. Our main gateway handles other traffic so I want to keep this link seperate. It will need to support HSRP in case of failover.

    Would the Cisco 871 router be up to the job for 2 VC units that are not heavily used?

    Thanks,

    Martin

    DB:2.66:Cisco 871 As A Router On A Stick 3j


    Hi guys,

    Thanks for all your replies. Looks like I will be able to do what I was hoping to.

  • RELEVANCY SCORE 2.66

    DB:2.66:Hello, Here Ricardo From Venezuela, I Have Upgrade To 6.0 Ios, Since That My Ipod Has Troubles To Stay Connect With Wifi, I&Acute;Ve Been Reviewed A Lot Of Suggestions Without Any Solution. Pls Help!!!! m3


    Hello, Here Ricardo from Venezuela, I have upgrade to 6.0 IOS, since that my Ipod has troubles to stay connect with WIFI, Ive been reviewed a lot of suggestions without any solution. Pls Help!!!!Gretting and Thanks!!!P.S: Ive checked all the connections and the router, the Ipod seems to get connected but I can't see even nGoogle on safari!

    DB:2.66:Hello, Here Ricardo From Venezuela, I Have Upgrade To 6.0 Ios, Since That My Ipod Has Troubles To Stay Connect With Wifi, I&Acute;Ve Been Reviewed A Lot Of Suggestions Without Any Solution. Pls Help!!!! m3

    Hello, Here Ricardo from Venezuela, I have upgrade to 6.0 IOS, since that my Ipod has troubles to stay connect with WIFI, Ive been reviewed a lot of suggestions without any solution. Pls Help!!!!Gretting and Thanks!!!P.S: Ive checked all the connections and the router, the Ipod seems to get connected but I can't see even nGoogle on safari!

  • RELEVANCY SCORE 2.66

    DB:2.66:Something About Different Method Using In Intervlan 3k



    What are the advantage and disadvantage among them?           

    Which of the following is the fastest?

    1, without Router on a stick, use a Router to connect each VLAN with a line

    2. Router on a stick

    3. Sub interface support by multilayer switch

    4. EIGRP

    DB:2.66:Something About Different Method Using In Intervlan 3k


    Hello Ho,

    the most efficient and current way to perform inter vlan routing is the use of SVI interfaces on multilayer switches.

    SVI interfaces are L3 interfaces associated to the corresponding L2 broadcast domain.

    So interface Vlan1 is associated to L2 broadcast domain Vlan1, interface Vlan2 to L2 broadcast domain vlan2 and so on.

    An SVI is a logical interface that is considered up/up if at least one L2 port is up/up  and in spanning-tree in forwarding state in the associated L2 Vlan (broadcast domain). The L2 port can be an access port with a PC connected to it or a trunk port that is member of multiple vlans at the same time,

    The SVI provides L3 services to hosts in the Vlan and typically acts as the default gateway for end user devices connected to the Vlan.

    The use of an external router with vlan based subinterfaces connected to a switch trunk is limited to those cases where a L2 only switch has been deployed like C2950 or C2960  (last IOS images of C2960 allows for some inter-vlan routing with limited features).

    There are some special cases that still require the use of subinterface on a router in the field of VOIP to connect IP phones of a remote office to a router that can provide limited signalling features in a remote branch office when the office is isolated from the HQ callmanager ( VOIP signalling server) this is called Survivable remote site telephony (SRST).

    A router may be needed for other special cases like network address translation between different parts of the network. But this aspect goes beyond inter vlan routing.

    The use of external router without trunk link/subinterfaces with per Vlan dedicated interface is really rare and limited to cases where a L2 only switch is connected to an old router that is not able to support subinterfaces, as it is clearly very poor in scalability as it requires a router interface for each served Vlan and  routers haven't many ports.

    The use of EIGRP or other interior gateway protocol like OSPF provides the capability to advertise IP subnets to multiple devices and has the benefits of dynamic routing

    You take advantage in using a routing protocol when multiple router and multilayer switches devices are present in your network and it is a good move to have them exchange routing information that includes the IP subnets associated to client Vlans.

    The high performance in inter vlan routing is achieved by using multilayer switches as stated above.

    The cost of multilayer switch is now really low specially considering cost per port and they work in hardware this explains their high performance.

    Note:

    we should speak of fastest way to perform forwarding of packets in a inter vlan context this is the meaning I have given to your question.

    Hope to help

    Giuseppe

  • RELEVANCY SCORE 2.66

    DB:2.66:Mbr624gu 3g Router And Rogers Rocket Internet Stick In Canada dp


    Hi, I just purchased a Netgear MBR624GU-100NAS 3G wireless router to use with my Rogers Rocket USB internet stick in Canada. The tech for the stick is ZTE. I never checked compatibility before, and even after the newest firmware update, it says my stick is not supported, confirmed by cust. support.

    There is a user on another forum claiming to have the same products working together, I PM'd him, but he has not replied. Is there a work-around or at least can I asks the mods to put in a request for support for my stick? These sticks are selling fast in Canada recently due to an aggressive price drop, so if it is just a simple firmware update, and if you have the manpower still, it would help sell at least a couple of thousand up here. Thanks.

    DB:2.66:Mbr624gu 3g Router And Rogers Rocket Internet Stick In Canada dp

    Hi Organno

    did you success? I have the same problem here. I need to install the non-us firmware in order to test the device, but it keeps saying file error with 6.00.28.43WW.

    Was anyone succefull in changing the firmware to use the router outside the US?

    Best Regards

    Rod

  • RELEVANCY SCORE 2.66

    DB:2.66:Cbac On Router Subinterface 7x


    Does anyone know if it is possible to use cbac between router subinterfaces in router on a stick situation between two vlans as internal vlan and external vlan?

    DB:2.66:Cbac On Router Subinterface 7x

    Does anyone know if it is possible to use cbac between router subinterfaces in router on a stick situation between two vlans as internal vlan and external vlan?

  • RELEVANCY SCORE 2.65

    DB:2.65:Troubles Connecting To The Internet With My Wireless Router 97


    I have a WRT54GS v7 wireless router, that I am using with a ZyXEL P-660R-D1 DSL modem. during setup I was unable to establish a connection to the internet once my router was connected properly to my desktop computer and my modem. All of the correct lights on both my modem and router are lit. Please help, I attempted turning off both as was instructed by the setup wizard, but that failed to make the internet connection work and I continued the setup process after many attempts. At the end of the setup it said that my router was set up but i did not have a connection to the internet. What should I do to fix this problem?






    Solved!
    Go to Solution.

    DB:2.65:Troubles Connecting To The Internet With My Wireless Router 97


    Thank you so much, this was a huge help. This problem has given me trouble for awhile now and its nice to feel relieved.

  • RELEVANCY SCORE 2.65

    DB:2.65:Router On A Stick? mx



    While I am waiting for my preordered ERL get delivered I wanted to look over the documentation. I haven't been able to find any mention of router on a stick configurations. Is it possible with the ERL? Do you have a config example?

    I have a data, voice, surveillance, and management vlan in the environment that this router will be installed. It would be nice to be able to route between the data and surveillance but exclude routing to the voice vlan from any of the other vlans with the new router.







    Solved!
    Go to Solution.

    DB:2.65:Router On A Stick? mx

    ElliottN wrote:

    I have a data, voice, surveillance, and management vlan in the environment that this router will be installed. It would be nice to be able to route between the data and surveillance but exclude routing to the voice vlan from any of the other vlans with the new router.

    There is also some discussion on isolating VLANs here.

  • RELEVANCY SCORE 2.65

    DB:2.65: Satellite C660-21c - Troubles With Ram Modules mp


    Hi

    I was considering upgrading my RAM for my C660-21C from 4gb to 8gb. I therefore decided to take out my 4gb ram in the ram slot to see the name type of it. After I had done this, I inserted it in however, now, when I press the power button, the laptop turns on for around 5 seconds then switches off.

    I have checked the ram stick in both slots and it’s definitely fitted properly. Could someone please tell me what the problem is? Am I dealing with a dead ram stick for whatever reason or have I done some other serious damage to the machine, i.e. static destroying the ram or whole machine?

    Could someone help troubleshoot my problem please?

    Thanks

    Chris

    DB:2.65: Satellite C660-21c - Troubles With Ram Modules mp

    Hi

    Yes, I disconnected AC and removed the battery before anything.

    All I did was take out the one 4gb ram stick look on the back to see the type and numbers so i could order the correct ram. Once i wrote the info down, I put it back into the same slot, its fitted fine, the clips are on it, simply screwed the cover back on put battery in. If i turn the laptop on now, it turns on for 7 seconds and just turns off, just a black screen. (ive tried the stick in both slots, no difference)

    My predicament though, have i destroyed the ram stick or slot with my static, if so do i go ahead and order new ram try it. If this fails, ive wasted money, i may even destroy those sticks! or is it more serious, could i have damaged other parts such as the motherboard.

    I purchased my laptop from the site 'saveonlaptops' I have around one month of the toshiba warranty left, Im going to call my local pc world know how tech guys to see if they will troubleshoot and/or fix it if its in warranty.

    Any oTher advice or troublershoot help is appreciated, I use this laptop for hours on a daily basis the sooner someone can help me pinpoint the issue, the sooner something can be done about it!

    Thanks

    Chris

  • RELEVANCY SCORE 2.65

    DB:2.65:Vlans - Router On A Stick 83



    Wondering if anyone can provide guidance on max users in a router on a stick (Cisco 2621) vlan implementation. Services are limited to email light web... I can't imagine the network growing over 70 users with all servers located on their own vlan. Switch connecting to the router is a CAT 4006.... I'm attempting to hold off buying the L3 card.

    If lan traffic is 20% with 70, 10MB users....we're looking at 140MB, which is beyond the capacity of the single 4006-2621 fast ethernet link. Is this the correct way to calculate probable load or is my thinking too simple?

    Thanks for the help....

    Jim

    DB:2.65:Vlans - Router On A Stick 83


    The beauty of LAN traffic in a scenario like this is that it isn't constant. I have seen far more users that 70, using 100 Mbps, run across this type of configuration. And keep in mind that your 2621 has 2 F/E ports. So if traffic does get too heavy for a VLAN trunk, you can put one port in one VLAN, and the second in the other.

  • RELEVANCY SCORE 2.65

    DB:2.65:Router On A Stick 93



    I have an isr 2851 and need to support multiple vlans on g0/0, I'm connecting to a layer 2 switch. Is a router on a stick my only option? Do the isr's support a trunk command, similar to the "switchport mode trunk" found on cat switches?

    DB:2.65:Router On A Stick 93


    thanks for the quick answer to my post.

  • RELEVANCY SCORE 2.65

    DB:2.65:Encapsulation Dot1q z8



    Hi All,

    I'm trying to be able to trunk a subinterface of a router (router on a stick) and I'm having a tough time understanding what IOS and type of router that will support this command. I've tried in one 2611 router but the command is not available, but I can't figure out which IOS I need in oder to do that. Any help would be greatly appreciate it.

    Cheers!

    DB:2.65:Encapsulation Dot1q z8


    You need a minimum feature set of IP Plus so if you have IP Base the command will not be available.

    Jon

  • RELEVANCY SCORE 2.65

    DB:2.65:Troubles Moving From Dsl (Wgr 614) To Cable p9


    I just had cable installed, and was hoping that I'd still be able to use my Netgear wireless WGR614 router as my main network hub. The installation guy said to continue to use the straight cable as the connection from the cable modem to the router (coax modem netgear router to PCs), but that didn't work (either wirelessly or direct connection). Do I have to buy a netgear wireless router built specifically for cable? Any/all help would be appreciated; Comcast couldn't "troubleshoot" my request )

    Greg

    DB:2.65:Troubles Moving From Dsl (Wgr 614) To Cable p9

    PS My residential neighbor is older than I am (I've been retired for ten years now) and if he wants to steal my internet service, he is welcome to do so. Passwords and encryption on computers with all file/program sharing off and firewalls on could be a royal pain and should be OFF while troubleshooting your initial connection. (I had to play with the antenna orientation on the router to reach my daughter's ibook in another room. sam

  • RELEVANCY SCORE 2.65

    DB:2.65:Nat Troubles With Xbox Live On A Wrtu54g-Tm Router. km



    So I have tried looking on YouTube and follow tons of instructions, I have tried making my own settings on everything, and honestly I have no idea what I am doing so that might be a big problem with why I cannot open it. I have just done what everyone says to do but it seems that my router type is unable to open the NAT how all other routers are able to. So if anyone knows how to open up the NAT on a WRTU54G-TM router, I would really appreciate the help.

  • RELEVANCY SCORE 2.65

    DB:2.65:Router On A Stick Help aj



    Hello, my name is Chris and  I am new to the discussion forums.  I am having trouble pinging pc-pc with my PKT Tracer configuration.  I have searched the forums and instructional vids but just can't seem to get the pc's to communicate.  Can anyone look at this for me?

  • RELEVANCY SCORE 2.65

    DB:2.65:Connect Usb Drive To D1000 Router zc



    Hi

    I am trying to connect a USB hard drive or memory stick to my D1000 Router. But

    i cannot see it via my laptop. And it does not appear on the "Virtual Device" on the router configuration when i log in.

    I have enabled file sharing to Public but still no joy.

    Any Help available please.

    Thanks Anthony

    DB:2.65:Connect Usb Drive To D1000 Router zc


    Hi

    I am trying to connect a USB hard drive or memory stick to my D1000 Router. But

    i cannot see it via my laptop. And it does not appear on the "Virtual Device" on the router configuration when i log in.

    I have enabled file sharing to Public but still no joy.

    Any Help available please.

    Thanks Anthony

  • RELEVANCY SCORE 2.65

    DB:2.65:Router On A Stick a3



    Hi,

    a have a cisco 1721 with a wic 4esw card and I am trying to configure two vlans to talk to each other thru the e0 port. would appreciate any help!!!

    DB:2.65:Router On A Stick a3


    As long as the VLANs have an associated SVI (logical VLAN interface) defined and configured with an ip address you should not have to do anything special to make them talk to eachother. What do you mean you want them to talk to eachother through e0? Can you post the configuration you have done so far?

  • RELEVANCY SCORE 2.65

    DB:2.65:Mobile Broadband Router Connection 91


    Hi

    I just bourght a PAYG mobile Broadband USB stick as a backup for when our
    ADSL connection fails. We are having trouble connecting the stick to our
    router. I can use the stick to connect to the internet from my laptop
    but can't get a connection through the router.

    Can anyone help.
    Thanks

    DB:2.65:Mobile Broadband Router Connection 91

    Okay guys, I got it working last night!

    Use these settings

    PP Client Mode= Enable
    Sim Pin Code:
    Modem Initial String APNp.internet
    APN name:
    Modem Dial String: ATCT*99#
    Username: web
    Password: web

    Now reboot the router and wait on it fully staring up, then when you see the blue flashing light on the Vigor donge disconenct it from the router for a few seconds and then plug it back in. Wait for about 30 seconds and you should see the light turn a steady blue colour. This means it is connected to a 3G signal, if you only have have GRPS in your are it the light will be green.

    Im using the latest firmware for the Vigor, If any one has problems drop me aline and Ill help.

    Regards

    Joe